DIGITAL MULTIMETER This instrument is a true RMS (root mean square) digital multimeter designed for measurements within the range of CAT. IV 600V and CAT. III 1000V. It is suitable for measurements in electrical work sites of low-voltage circuits. ●Full 4-digit 9999 count ●True RMS ●EF (Electric Field) sensing ●AUTO V function automatically distinguishes between DC and AC voltage. ●Auto Hold function automatically holds the measurement value once it stabilizes. ●Large, easy-to-see display ●Compact, lightweight, easy-to-hold design ●Auto power off after approx. 30min of inactivity(cancelable) ●Bright backlight SPECIFICATIONS DCV ACV Resistance Capacitance Frequency Continuity EF detection Best accuracy Resolution Measuring range 0.1mV ±(0.5%+2) 999.9m/9.999/99.99/999.9V 0.1mV ±(1.0%+5) 999.9m/9.999/99.99/999.9V 0.1Ω ±(0.5%+5) 999.9/9.999k/99.99k/999.9k/9.999M/99.99MΩ 0.1nF ±(5%+5) 999.9n/9.999µ/99.99µ/999.9µ/9.999m/99.99mF 0.001Hz ±(0.1%+5) 9.999/99.99/999.9/9.999k/99.99kHz Buzzer sounds at 30 to 70Ω or less Open voltage: approx. 0.6V Detects ACV and EF of approx. 80V or more Operation method AC detection method Display Sampling rate Over-range display Range selection Polarity switching Battery low warning Δ-Σ method True RMS (AC coupling) Max. 9999 counts Approx.5 times/sec. (DCV) "OL" shown in numeric section Auto and manual Automatic selection (Only "-" is displayed.) lights up on display when supply voltage from internal batteries drops below about 2.5V. Operating environmental condition Altitude no more than 2000 m, indoor use, environmental pollution degree II Operating temperature / humidity Temperature: 5 to 40℃ Humidity is as follows (without condensation) . 5 to 31℃: Max.80％RH 31 to 40℃: Linearly decreases from 80% RH to 50% RH. Storage temperature / humidity Temperature -10 to +40℃：No more than 80% RH, without condensation Temperature +40 to +50℃: No more than 70% RH, without condensation Power consumption Approx.2 mA (during DCV measurement, with backlight off) Battery life Approx.550 hours (during DCV measurement, with backlight off) Safety standards IEC61010 CAT. IV 600V / CAT. III 1000V EMC Directive IEC61326 Bandwidth 40 - 400 Hz Battery LR03 X 2 Size / Mass H149 X W72 X D37 mm / approx. 232 g Standard accessories included Test lead (ATL101), Instruction manual Dempa Bldg, 4-4 Sotokanda 2-Chome, Chiyoda-Ku, Tokyo 101-0021 Japan Tel:+81-3-3251-0941 Fax:+81-3-3256-9740 A battery for monitoring has been installed prior to shipment from the factory. It may be discharged before the expiration of the described battery life. This battery is used to check the functions and performance of the product.Specifications and external appearance of the product described above may be r

DIGITAL MULTIMETER This function detects the electric field generated by AC voltage. Compact design Test lead holders These are useful for test leads storing, and also enable users to take measurements with one hand. AUTO HOLD function When a new stable measurement value is detected in the Auto Hold mode, the buzzer sounds, and the new measurement value is automatically held. Tilt stand This enables the device to stand at an angle on a table etc. and users to take measurements with both hands. This function automatically detects whether the input voltage is AC or DC. Hanger magnet HM-1 (optional...