ANNEXURE - III BRIEF DISCRETION OF ELECTRONIC TAXI/AUTOMETER MODEL : SANSUI - 786 The Digital Taxi/Autometer is a transparent and tamper-proof. The meter functions with two independent variables i.e. - distance traveled by the commuter and waiting time. The dependent parameter is fare to be paid by the commuter as per Govt, fixed tariff. A) DISTANCE MODE: When the meter is flagged down or in hired position, it shows cetain minimum fare for 1km.(as per Pune tariff), 1.6km (as per Mumbai tariff), and 2km. for auto and 4km. for radio-taxi, respectively in Bangalore. Thereafter the meter shows the fare for every 1/1 Okm. distance, in advance as per the approved Govt, tariff. For Pune, the initial drop Rs.6/km. and the subsequent money drops for every 100m. distance traveled i.e. 0.1 km.=Rs.0.40 i.e., therefore the distance tariff - Rs. 4/km. That is the moment when 1.0 km. crosses, the meter shows Rs.6.40 and subsequently over 0.1km. - advance drop of Rs. 0.40 jump would occur in the meter. B) TIME TARIFF: The commuter has to pay waiting time fare according to the approved tariff. In Pune, the time tariff = 2min. 30sec., one money drop occurs in the meter. Therefore, time tariff = Rs. 9.60/hr. C) CHANGE OVER SPEED: Change over speed = time tariff= Rs. 9.60/hr. = 40m/min. distance tariff Rs.4/km. If the vehicle moves below the changeover speed, i.e. 40 m/min., then the time mode still activates showing the fare to waiting time i.e. over 2.5 min., one money drop will occur. If the vehicle moves greter than the changeover speed, the meter would go into the distance mode. Therefore, the changeover speed parameter is a creterion for the meter to decide, whether the meter will go into time mode or distance mode, which are independent variables. The meter is transparent in the sense; it has 6/5 displays (9999.80) for indication of fare in rupees and paise, 4 displays for indicating distance (999.9) in km. and 4 displays for indicating waiting time, and one digit to show display status. D) WAITING TIME: 4 digits for waiting time i.e. hours, minutes and real time clock of 4 digits in hours and minutes. The keys provided are of "VACANT', "HIRED”, "STOP", and "TARIFF". In case of Electronic Faremeter,' k' factor = No. of pulses per km. If' k' = 700 puises/km. Night tariff (2200hrs. to 0600hrs.) is 1.5 times or 1.25 times according to the approved over-night charges. The meter is automatically changes the fare structure, as per approved tariff. SANSUI ELECTRONICS

SANSUI AUTO/TAXI METER MODEL NO. SANSUI-786 ANNEXURE - IV P«toe - l PHYSICAL DIMENSIONS OF THE TAXI/AUTOMETER : SIDE VIEW SANSUI ELECTRONICS

SANSUI AUTO/TAXI METER MODEL NO, SANSUI- 786 ANNEXURE - IV - ft PHYSICAL DIMENSIONS OF THE TAXI/AUTOMETER : SKETCH AND SECTIONWISE DRAWING

SKETCH AND SECTIONWISE DRAWING DISPLAY PANEL OF FAREMETER: 5 or 6 Digits (Display Grp. 1) for FARE of Digit Height = 18mm. as per 5.6.1 and 5. Display self illuminating as per 5.6.5.1 Amount LED used in Report Mode only Time LED used in Report Mode only Kms. LED used in Report Mode only Waiting Time LED will be ON in Waiting Modi Night LED On in Night Mode Baggage LED ON when Baggage is fed 4 Digits (Display Grp.3) for Parameters/Distance TravellUfi Digit Height = 10mm 1 Digits for Status of Display Grp. 3/Parameter No./Pulse Inp; as per 5.6.2.1 4 Digits for (Display Grp. 2) RTC/Waiting Time/Pulse...

ANNEXURE- V METHOD OF OPERATION OF THE TAXI/AUTOMETER MODEL SANSUI - 786 : Position of the flag in different modes of Rickshaw / Taxi meter 1. For Hire Mode When the rickshaw / Taxi is vacant, the flag should be in "Vertical Up" podition. In this position of the flag the meter will indicate "For Hire" as shown in figure 1 2. Hire Mode When the commuter sits in Rickshaw / Taxi, to start the meter the flag should be rotated counter clock wise to "Vertical Down" position as shown in Fig. 2 Here Distance travelled OR Waiting time will get engaged depending on the changeover speed. 3. Stop Mode For...

METHOD OF OPERATION OF THE TAXI/AUTOMETER MODEL SANSUI-786: A) When the faremeter is properly connected to its own matching sensor assembly. B) When the faremeter is not properly connected to the sensor assembly or some fault has occured in the sensor assembly or some spurious external unauthorised sensor assembly is connected or is tampered. CONDITION B : If the Sensor wire is not connected properly to the meter then SANSUI will blink thrice in Display Group land then after few seconds Display Group 1 will continuously blink showing "F. HirE" and Display Group 2 will show "RTC” and Status Display...

METHOD OF OPERATION OF THE TAXI/AUTOMETER MODEL SANSUI - 786 : ANNEXURE- V Initially when the reckshaw is vacant the flag will be in top position and meter will be in For Hire mode.When a commuter hires the reckshaw, the driver rotates the flag to bottom position counterclock wise. In this position of the flag the meter is turned to Hired mode and it starts displaying fare according to respective tarrif. On reaching the commuters destination the driver will rotate the flag counter clock wise to 90 degree and the meter will turn to stop mode. In this mode there will not be any increament in fare...

Ptxg-e — >4 (Working position as per 5.5.5 and 5) When the Auto is hired by the commuter the driver rotates Flag to Vertical Down position i.e. HIRED mode. Display Group 1: It will show fare as XXXX.XX corresponding to initial distance and initial time - as (5.6.3) & (5.4.1) Display Group 2: a) It will show the Real Time Clock if the vehicle is running at a speed above the change over speed, b) Display Grp. 2 will show distance travelled in HIRED mode - as 5.5.5 a) Distance Mode : - as per 5.4.2(a) and 5.4.7 Real Time Clock if vehicle in distance mode i.e. vehicle runnirsi above change over speed...

METHOD OF OPERATION OF THE TAXI/AUTOMETER MODEL SANSUI - 786: When the commuter reaches his destination the vehicle stops and the driver rotates flag to horizontal right position i.e. STOP mode. ^--Fare —Waiting Time displayed in blinking format as Distance travelled in kms. as XXX.X Night LED ON if in night mode Bags LED ON if baggage amount has been entered. When the meter is in STOP mode, following is shown on the display Display Group 1: It will show fare as XXXX.XX - as per (5.5.6) & (5.4.1) Display Group 2: It will show the waiting time in blinking mode as HH:MM Status Display : It will...