GEAR PUMPS AND MOTORS "B" SERIES Technical catalogue

E0.16.0610.02.02 The data in this catalogue refers to the standard product. The policy of Salami S.p.A. consists of a continuous improvement of its products.It reserves the right to change the specifications of the different products whenever necessary and without giving prior information. If any doubts, please get in touch with our sales departement.

GEAR PUMPS AND MOTORS Working conditions P2 = Intermittent operating pressure (1/3 of working time) P1 = Continuous operating pressure SALAMI gear pumps are available with displacements from 5.5 cm3/rev to 44 cm3/rev(from 0.36 cu.in./rev to 2.69 All pumps are available as multiple units either of the same or different series. With all sizes of pumps and motors there are options of shafts, flanges and ports as for European, German and American standards. SALAMI gear pumps and motors offer: • High volumetric efficiency by innovative design and accurate control of machining tolerances. • Axial compensation...

GEAR PUMPS AND MOTORS "B" SERIES Features DRIVE SHAFT Radial and axial loads on the shafts must be avoided since they reduce the life of the unit. Pumps driven by power take - off on engines must always be connected by placing an "Oldham" coupling or coupling having convex toothed hub. This is to ensure that inevitable misalignment during assembly is reduced to minimum. PUMP AND MOTOR ROTATION DIRECTION VIEWED AT THE DRIVE SHAFT Anti - clockwise rotation PUMP Clockwise rotation PUMP Reversible rotation PUMP/MOTOR Inlet Clockwise rotation MOTOR Anti-clockwise rotation MOTOR HYDRAULIC PIPE LINE...

GEAR PUMPS AND MOTORS FILTRATION INDEX RECOMMENDED COMMON FORMULAS FOR PUMPS COMMON FORMULAS FOR MOTORS Input flow: Output torque: Output power: V = Displacement crrf/rev [in-Vrev] Poul = Outlet pressure bar [psi] IP - PouI - F;n(system pressure) bar [psi] For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS DESCRIPTION OF THE NEW PRODUCT IDENTIFICATION LABEL Based on the firm certification ISO 9001 - UNI EN 29001, section 4.8 (identification and tracebility of the product), we have adopted a new identification label starting from the 1st march 1995. Pis, see following example: A = Product short descritpion (eg. VD8A/FDD/U4G). B = Customer part number. C = Salami part number (eg. 6235 0025 0). D = Production code (for Salami management) E = Rotation sense (only for pumps). F = Production date (see data sheet here below) G = Progressive number of assembling. (except triple 2PB)...

GEAR PUMPS AND MOTORS "B" SERIES ROTATION CHANGING INSTRUCTIONS FOR PUMPS GROUP 2.5 Before starting, be sure that the pump is cleaned externally as well as the working area to avoid that particles dangerous for pump working can find their way into the pump. Pump represented is aclockwise rotation pump. To obtain an anti_clockwise rotation read carefully the following instructions. Picture "A" 1 - Loosen and fully unscrew the screws. 2 - Lay the pump on the working area in order to have the mounting flange turned upside. 3 - Coat the shaft extension with grease to avoid damaging the shaft seal....

GEAR PUMPS AND MOTORS "B" SERIES COMBINATION WITH TYPES OF FLANGES AND DRIVES SHAFTS AVAILABLE For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES Displacements up to 2.69 cu.in./rev Pressure up to 4300 psi GEAR PUMPS AND MOTORS ASSEMBLING DIMENSIONS AND VALUES OF PRESSURE AND SPEED Type Displacement Dimension A Dimension C Working pressure Intermittent pressure Peak pressure IMPORTANT: The displacements 5.5 - 8.3 - 11.5 - 13.8, are always available as rear pump. Displacements 11.5 - 13.8 are available as single pump only with drive shaft "55" 70 - 75 Nm (51.6 - 55.3 lbf-ft) Body height 7 For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES 2.5P/MB FLANGED PORTS D Depht. e For the other displacements, please contact our sales department. Available for quantity (contact our sales dept.) Available for quantity (contact our sales dept.). British standard pipe parallel (BSPP) For more information: WWW.SALAMI.IT

REVERSIBLE GEAR MOTORS "B" SERIES code P THREADED PORTS Y Type Available for quantity (contact our sales dept.). British standard pipe parallel (BSPP) The assembly differences betwen pump or motor is only the lipped spacer. The other important difference between pump and motor is the run-in duty cycle. The motor cycle is deeper, this is due to the fact the motor has to ensure a minimum starting torque. 9 For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES code 53 Splined SAE A 10T-16/32DP Available for quantity (contact our sales dept.) code 54 SAE A 11T-16/32DP Ansi B92 1a 1976 Available for quantity (contact our sales dept.) For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES With drive shaft code 38 With drive shafts code 53 - 54 - 55 - 87 With drive shafts code 55-87 11 For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES With shaft code 66 Flange on gear box ZF With shaft code 38 For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES Standard cover for reversible pumps and motors, with external drain port ØC. For dimension ØC please see the table here below. Standard rear cover for unidirectional pumps. REAR COVERS WITH INLET/OUTLET PORTS 35 Rear cover with INLET/OUTLET ports, for unidirectional pumps and motors. INLET Rear cover with INLET/OUTLET ports and external drain Ø C, for bidirectional pumps and motors. D In phase of order please specify D and C dimensions 13 For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES REAR COVER WITH MAIN RELIEF VALVE Rear cover with fixed setting main relief valve. Available values of fixed setting (bar/psi) Main relief valve with internal unloading line. For more information: WWW.SALAMI.IT

GEAR PUMPS AND MOTORS "B" SERIES REAR COVER WITH PRESSURE COMPENSATED FLOW CONTROL VALVE SIDE PORTS Pressure compensated flow control valve with excess flow to tank Priority flow ports Excess flow ports Pressure compensated flow control valve with excess flow to tank, with main relief valve on controlled flow line. AXIS OF PUMP SHAFT ANTI-CLOCKWISE ROTATION Priority flow valve valve Pressure relief valve AXIS OF PUMP SHAFT CLOCKWISE ROTATION CALIBRATED ORIFICE Ø d(mm/inch) FLOW RATE (l/min - gpm) ± 10% time for supplying two separate circuits defined priority flow remains constant regardless...