GEAR PUMPS "E" SERIES - GROUP 2 Technical catalogue

E0.23.1011.02.01 The data in this catalogue refers to the standard product. The policy of Salami S.p.A. consists of a continuous improvement of its products.It reserves the right to change the specifications of the different products whenever necessary and without giving prior information. If any doubts, please get in touch with our sales departement.

GEAR PUMPS P2 = Intermittent operating pressure (1/3 of working time) P1 = Continuous operating pressure SALAMI gear pumps are available with displacements from 3.2 cm3/rev to 26 cm3/rev(from 0.19 cu.in./rev to 1.59 All pumps are available as multiple units either of the same or different series. With all sizes of pumps and motors there are options of shafts, flanges and ports as for European, German and American standards. SALAMI gear pumps and motors offer: • High volumetric efficiency by innovative design and accurate control of machining tolerances. • Axial compensation achieved by the use...

GEAR PUMPS "E" SERIES Features DRIVE SHAFT Radial and axial loads on the shafts must be avoided since they reduce the life of the unit. Pumps driven by power take - off on engines must always be connected by placing an "Oldham" coupling or coupling having convex toothed hub. This is to ensure that inevitable misalignment during assembly is reduced to minimum. PUMP ROTATION DIRECTION VIEWED AT THE DRIVE SHAFT Anti - clockwise rotation Clockwise rotation Reversible rotation HYDRAULIC PIPE LINE To ensure favorable suction conditions it is important to keep pressure drop in suction pipe line to a...

GEAR PUMPS "E" SERIES Features FILTRATION INDEX RECOMMENDED Working pressure Achieved with filter ßx =75 FIRE RESISTENT FLUID Type oil emulsion with 40% water Water glycol Phosphate esters COMMON FORMULAS LEGENDA Dp = Working pressure (bar) q = Displacement (cm3/rev) 3 For more information: WWW.SALAMI.IT

GEAR PUMPS DESCRIPTION OF THE NEW PRODUCT IDENTIFICATION LABEL Based on the firm certification ISO 9001 - UNI EN 29001, section 4.8 (identification and tracebility of the product), we have adopted a new identification label starting from the 1st march 1995. Pis, see following example: A = Product short descritpion (eg. VD8A/FDD/U4G). B = Customer part number. C = Salami part number (eg. 6235 0025 0). D = Production code (for Salami management) E = Rotation sense (only for pumps). F = Production date (see data sheet here below) G = Progressive number of assembling. (except triple 2PB) the identification...

GEAR PUMPS "E" SERIES ROTATION CHANGING INSTRUCTIONS FOR PUMPS GROUP 2 Before starting, be sure that the pump is cleaned externally as well as the working area to avoid that particles dangerous for pump working can find their way into the pump. Pump represented is aclockwise rotation pump. To obtain an anti_clockwise rotation read carefully the following instructions. Picture "A" 1 - Loosen and fully unscrew the screws. 2 - Lay the pump on the working area in order to have the mounting flange turned upside. 3 - Coat the shaft extension with grease to avoid damaging the shaft seal. 4 - Remove...

GEAR PUMPS "E" SERIES COMBINATION WITH TYPES OF FLANGES AND DRIVES SHAFTS AVAILABLE Note: other versions available, see shafts and flanges information. For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES Displacements up to 1.58 cu.in./rev Pressure up to 4300 psi GEAR PUMPS ASSEMBLING DIMENSIONS AND VALUES OF PRESSURE AND SPEED Type cm3/rev cu.in./rev mm Dimension A in mm Dimension C in bar Working pressure p1 psi bar Intermittent pressure p2 psi bar Peak pressure p3 psi * Available only as rear pump Performance curves carried out with oil viscosity at 16 cSt and oil temperature at 60°C For flanges code: P1 - B1 - S2 - S6, this dimension is 19 mm (0.75 in.) B2 - B3 - B4 - B5, this dimension is 16.5 mm (0.65 in.) A ASSEMBLING EXAMPLES 7 For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES code B THREADED PORTS Y British standard pipe parallel (BSPP) 0.5 mm 0.02 inch For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES Tang drive for diesel engines. For flange K1 without shaft seal. Tang drive for electric motors. Without shaft seal. Tang drive. Woodruff key (3.165x6.5) Woodruff key (3.165x14) for bearing versions Woodruff key (3x6.5) Woodruff key (3x5) for bearing version CL-CF with flange thickness 19 mm with flange thickness 16.5 mm with flange thickness 19 mm with flange thickness 16.5 mm 9 For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES with flange thickness 19 mm with flange thickness 16.5 mm The dimension 31.8, is referred to flange thickness 19. In case of flange thickness 16.5, please contact our sales dept. internal splined Max. torque 115 Nm The dimension 31.8, is referred to flange thickness 19. In case of flange thickness 16.5, please contact our sales dept. DIN 5480 internal splined Only for rear pumps With shaft code 25-62 82 (3.23) With shaft code 03 With shaft code 03 For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES With shaft code 25-62 With shaft code 25-62 With shaft code 52-54-82-85. With shaft code 52-54-55-82-85 With shaft code 52-54-82-85 11 For more information: WWW.SALAMI.IT

With shaft code 52-54-82-85 For Iveco engines GEAR PUMPS "E" SERIES With shaft code 02. For Perkins engines (series 100) PINION GEAR CODE 3122 025 30 NUMBER OF TEETH 20 BASE CIRCLE DIAMETER 42.617 mm HAND OF HELIX RIGHT HELIX ANGLE 13°14'3" With shaft code 28 The combination 28MF is not comprehensive of pinon gear. The pinion gear must be specified in phase of order. For more information: WWW.SALAMI.IT

GEAR PUMPS "E" SERIES Order example pump 2PE with bearing: 2PE16D - B25 B4 - CL Life of bearing under following condition: L=18 mm ( 0.71" ) D (Pulley diameter)=90 mm ( 3.54" ) To calculate the absorbed pump or motor torque, please use the following formula: For Code CP-CB-CL-CS Torque (Nm) *Available for quantity, please contact our sales department. 13 For more information: WWW.SALAMI.IT