SagiCofim Ecoefficiency for Indoor Air Quality

Adjusting damper 100 pitch SagiCofim Use range of the damper: in ATEX version in SAFE area - 20 ° C< t < + 50 ° C - Vmax 15 m/s - Pmax 3000 Pa - 20 ° C < t < + 70 ° C - Vmax 25 m/s - Pmax 3000 Pa A B C D E F G H I Specific features of the product Note: in the ATEX version, the damper is equipped with a a specific label and earthing cable. To establish the actual use range, check the data in the technical data sheet for the combined motors. Up to size 1500 x 1500. Over, in two pieces.

Adjusting damper 100 pitch SagiCofim Dimensional Measurements are in (mm)

Adjusting damper 100 pitch GTE 10 Manual commands Measurements are in (mm) Automated version Over 1.2 m2 Command weight 0.7 kg • All the manual commands are equipped with a lever locking mechanism in the requested position. • The damper can be equipped with electric motors for the Safe area and the ATEX area, both on / off and modular and with spring return. • The maximum dimensions of the motor without accessories are: BELIMO: X = 80 mm; Y = 250 mm SCHISCHEK X =  100 mm; Y = 210 mm • ON REQUEST Motors assembled inside the a

Adjusting damper 100 pitch GTE 10 Diagram 1 - Pressure drop and sound power level Pressure drop referring to sample 1000 x 1010 mm Degrees of damper opening 90°

Adjusting damper 100 pitch SagiCofim Tab. 3 Maximum torque (Nm) H B (mm) (mm) 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 NOTE: The torque values, outlined in the table, are intended for correct movement and total closure of the damper. For the dimensions not outlined in the table, refer to the torque values of the immediately larger size. Weights refer to dampers only without commands or motors. B > 1500 : two sections divided by a central separator, one command pin H > 2010 : reinforcement rods mid height

Adjusting damper 100 pitch GTE 10 Motor selection guide The values, outlined, of the motor torque are nominal values (i.e. the minimum guaranteed value in all use conditions according to the technical data sheet of the motor). Torque 2 Nm Torque 5 Nm WITHOUT In light operating conditions: a motor can be combined with the damper with a nominal torque 20% lower than the maximum torque required by the damper (see tab. 3). CM 24 SR - L-R; IP 54; VROT = 75 sec LM 24-230 A - SR; IP 54; VROT = 150 sec InMax - 5.10-Y; IP 66; VROT = 7.5 / 15 / 30 / 60 / 120 sec spring return ExMax - 5.10 Y; IP 66; VROT...

Adjusting damper 100 pitch LM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact InMax - 5.10; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec InMax - 5.10-S; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec; 2 fixed contacts spring return SAFE AREA spring return Damper ON - OFF Function spring return NM 24-230 A; IP 54; VROT = 150 sec NM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact InMax-15.30; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec InMax-15.30-S; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec; 2 fixed contacts SM 24-230 A; IP 54; VROT = 150 sec SM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact...

Adjusting damper 100 pitch GTE 10 Diagram 2 - Casing leakage (Class B) 5 UNI EN 1751 CL B Diagram 3 - Closed damper leakage (Class 2) 210 Pressure (Pa) Sample tests carried out on sizes 1000 x 1010 mm, in our laboratory. Results can be extended to the entire dimensional range of the product (see tab.1 page 4). Instrumentation, measurement and control systems in compliance with Standard EN 1751. Laboratory created in collaboration with the Politecnico di Milano, Engineering Faculty. ISO 9001 and ISO 14001 Certified Company. * Average performance

Adjusting damper 100 pitch Comfort Assembly applications • Fastening to duct using M 6 bolts. • Seal between the damper flange and duct. • Do not install in areas subject to stress phenomena, i.e. vibrations, bending or cyclic torsion. • Do not deform or twist the frame during maintenance and installation operations. • Install in areas protected from atmospheric agents. Maintenance • Before any intervention on the product use the planned IPD and then cut power to the command systems. • To clean, use substances or liquids that are NON-acidic and NON-abrasive • Do not paint levers or pins •...

SagiCofim spa Comfort Filtration Engineering via Firenze 1 20063 Cernusco sul Naviglio MilanItaly tel +39 02 929021 fax +39 02 92902300 [email protected] www.sagicofim.com Sagicofim S.p.A. reserves the right to make changes or amendments at any time without being obliged to give advance notification in relation to information in this publication.