SagiCofim Ecoefficiency for Indoor Air Quality

Adjusting damper 150 pitch SagiCofim Use range of the damper: in ATEX version in SAFE area - 20 ° C< t < + 50 ° C - V max 15 m/s -- 20 ° C < t < + 70 ° C - Vmax 25 m/s - Specific features of the product Note: in the ATEX version, the damper is equipped with a a specific label and earthing cable. To establish the actual use range, check the data in the technical data sheet for the combined motors.

Adjusting damper 150 pitch SagiCofim Dimensional Measurements are in (mm)

Adjusting damper 150 pitch GT 015 Manual commands Measurements are in (mm) OPEN CLOSED Automated version Over 1.2 m2 Command weight 0.7 kg • All the manual commands are equipped with a lever locking mechanism in the requested position. • The damper can be equipped with electric motors for the Safe area and the ATEX area, both on / off and modular and with spring return. • The maximum dimensions of the motor without accessories are: BELIMO: X = 80 mm; Y = 250 mm SCHISCHEK X =  100 mm; Y = 210 mm • ON REQUEST Motors assembled inside the a

Adjusting damper 150 pitch SagiCofim Diagram 1 - Pressure drop and sound power level Pressure drop referring to sample 1000 x 1060 mm Degrees of damper opening 90° 60° 40° 20°

Adjusting damper 150 pitch SagiCofim Tab. 3 Maximum torque (Nm) H B (mm) (mm) 200 300 ^ 500 600 700 800 goo 1000 110Q 1200 1300 1400 1500 1600 1y00 1800 1g00 2000 NOTE: The torque values, outlined in the table, are intended for correct movement and total closure of the damper. For the dimensions not outlined in the table, refer to the torque values of the immediately larger size. Tab. 4 Dimensions and weights for single section structure 1 Weights refer to dampers only without commands or motors. B > 2000 : two sections divided by a central...

Adjusting damper 150 pitch GT 015 Motor selection guide The values, outlined, of the motor torque are nominal values (i.e. the minimum guaranteed value in all use conditions according to the technical data sheet of the motor). Torque 2 Nm Torque 5 Nm WITHOUT In light operating conditions: a motor can be combined with the damper with a nominal torque 20% lower than the maximum torque required by the damper (see tab. 3). CM 24 SR - L-R; IP 54; VROT = 75 sec LM 24-230 A - SR; IP 54; VROT = 150 sec InMax - 5.10-Y; IP 66; VROT = 7.5 / 15 / 30 / 60 / 120 sec spring return ExMax - 5.10 Y; IP 66; VROT...

Adjusting damper 150 pitch LM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact InMax - 5.10; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec InMax - 5.10-S; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec; 2 fixed contacts spring return SAFE AREA spring return Damper ON - OFF Function spring return NM 24-230 A; IP 54; VROT = 150 sec NM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact InMax-15.30; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec InMax-15.30-S; IP 66; VROT = 3 / 15 / 30 / 60 / 120 sec; 2 fixed contacts SM 24-230 A; IP 54; VROT = 150 sec SM 24-230 A-S; IP 54; VROT = 150 sec; 1 adjusting contact...

Adjusting damper 150 pitch GT 015 Diagram 2 - Casing leakage (Class B) 5 UNI EN 1751 CL B Diagram 3 - Closed damper leakage (Class 2) 210 Pressure (Pa) Sample tests carried out on sizes 1000 x 1060 mm, in our laboratory. Results can be extended to the entire dimensional range of the product (see tab.1 page 4). Instrumentation, measurement and control systems in compliance with Standard EN 1751. Laboratory created in collaboration with the Politecnico di Milano, Engineering Faculty. ISO 9001 and ISO 14001 Certified Company. * Average performance

Adjusting damper 150 pitch Comfort Assembly applications • Fastening to duct using M 6 bolts. • Seal between the damper flange and duct. • Do not install in areas subject to stress phenomena, i.e. vibrations, bending or cyclic torsion. • Do not deform or twist the frame during maintenance and installation operations. • Install in areas protected from atmospheric agents. Maintenance • Before any intervention on the product use the planned IPD and then cut power to the command systems. • To clean, use substances or liquids that are NON-acidic and NON-abrasive • Do not paint levers or pins •...

SagiCofim spa Comfort Filtration Engineering via Firenze 1 20063 Cernusco sul Naviglio MilanItaly tel +39 02 929021 fax +39 02 92902300 [email protected] www.sagicofim.com Sagicofim S.p.A. reserves the right to make changes or amendments at any time without being obliged to give advance notification in relation to information in this publication.