S&C 5800 Series Automatic Switch Controls With IntelliTEAM II™ Automatic Restoration System Product Description TABLE OF CONTENTS Section INTRODUCTION Qualified Persons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Read this Instruction Sheet . . . . . . . . . . . . . . . . . . . . . . . 2 Retain this Instruction Sheet. . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Latest Document Release . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INFORMATION Understanding Safety-Alert Messages . . . . . . . . . . . . . . 3 Following Safety Instructions . . . . . . . . . . . . . . . . . . . . . 3 Replacement Instructions and Labels . . . . . . . . . . . . . . 3 Location of Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . 4 DESCRIPTION IntelliTEAM II System . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 S&C 5800 Series Switch Control Overview . . . . . . . . . . 5 S&C 5800 Series Switch Control Features . . . . . . . . . . 8 Additional S&C 5801 Features . . . . . . . . . . . . . . . . . . . . 9 Additional S&C 5802/5803 Features . . . . . . . . . . . . . . . . 9 S&C ELECTRIC COMPANY Specialists in Electric Power Switching and Protection

INTRODUCTION Qualified Persons !WARNING The equipment covered by this publication must be installed, operated, and maintained by qualified persons who are knowledgeable in the installation, operation, and maintenance of overhead electric power distribution equipment along with the associated hazards. A qualified person is one who is trained and competent in: • The skills and techniques necessary to distinguish exposed live parts from non-live parts of electrical equipment. • The skills and techniques necessary to determine the proper approach distances corresponding to the voltages to which the...

SAFETY INFORMATION Understanding Safety-Alert Messages There are several types of safety-alert messages which may appear throughout this instruction sheet as well as on labels attached to the S&C 5800 Series Automatic Switch Control. Familiarize yourself with these types of messages and the importance of the various signal words, as explained below. !DANGER “DANGER” identifies the most serious and immediate hazards which will likely result in serious personal injury or death if instructions, including recommended precautions, are not followed. !WARNING “WARNING” identifies hazards or unsafe practices...

SAFETY INFORMATION Location of Safety Labels

DESCRIPTION IntelliTEAM II System 5800 Series Controls with the IntelliTEAM II System let Scada-Mate® Switches, OmniRupter® Automated Switching Systems, Remote Supervisory Vista®, and pad-mounted distribution switches, or a combination of these, form teams that provide fast, fully automatic fault isolation and service restoration. Up to two automatic switch positions of the pad-mounted gear can be utilized, and configured independently, to provide further flexibility for the transfer process. Using peer-to-peer communications and distributed intelligence, team members protect a line segment by...

Mounting Channel LCD & Scroll Switches Faceplate LEDs & Switches Local Communications Access Port Door Pocket Switch Control Enclosure Door Retainer Switch Interface Connector(s) Faceplate Retainer Figure 1. Switch Control with Enclosure Door Open (S&C 5801 shown) Switch control enclosure (if applicable) – Sturdy, corrosion resistant aluminum box provides weatherproof and tamper-resistant protection for the switch control components. Switch interface connector(s) – Provides a connection point on the bottom of the switch control enclosure for cables carrying sensor data and control/status signals;...

Universal Communications Mounting Plate Switch Control Electronics Modules Communications Equipment (optional) Grounded AC Outlet Figure 2. Switch Control with Faceplate Open (S&C 5801 shown) Switch control electronics modules – Modularized for easy troubleshooting and replacement. Universal Communications Mounting Plate – A solid base on which the equipment for SCADA and team communications (radio, modem, etc.) is mounted. Communications equipment – The IntelliTEAM II system uses DNP protocol and a radio, modem, or other device for peer-to-peer communication and for 2-way communication between...

5800 Series Switch Control Features All controls in the S&C 5800 series include the following features: Dependable quality – Electronics manufactured in an ISO 9002-certified plant. Tough and reliable – Designed to withstand the difficult environmental and electrical conditions found in electric distribution applications. Rugged, well-proven core electronics design – Microprocessor, memory, and all related components based on technology developed for S&C’s full range of control products (with over 100,000 units in the field since 1985). Data logging capabilities – Useful for both stand-alone...

Your S&C 5801 switch control also includes special features which customize it for use with overhead switches. These features include: Custom ac voltage and current-signal conditioning – Specifically designed and tested for use with the type of sensors in use. Specialized enclosure wiring – Switch interface connector and internal enclosure wiring matched to the control cable. Switch control shipped ready to install – Control is modular with prewired connectors, and requires no discrete field wiring other than 120 Vac control power. Visual disconnect – Supports the S&C D2 visual disconnect option...