Elite SM
2Pages

GENERAL SPECIFICATIONS / ALL MODELS OF ELITE SM BOOMS • PU-40 Power unit includes a 40 hp electric motor, an electric panel, a cut-off switch, a double gear pump, a thermostatic oil cooler, a 44 US gallon oil tank, a support structure and hood. • 1000 watt anti-freeze immersed heater with thermostat on PU-40 oil tank. • Continuous rotation through a 12 port hydraulic swivel and a 5 section electric swivel. • 50 feet extension cable from joysticks to Danfoss control valve. • 50 feet extension cable for emergency cutoff switch and lights. • 40 feet extension cable to connect loader valves and accessories to PU-40. • An operator station mounted on the turret and including the operator seat, the hydraulic control valve assembly mounted under the operator’s seat, 2 mechanical joysticks mounted on the valves. The operator station is ready to receive an optional cab. • PU-40 Power unit includes a 40 hp electric motor, an electric panel, a cut-off switch, a double gear pump, a thermostatic oil cooler, a 44 US gallon oil tank, a support structure and hood. A secondary start/stop/accessories control box installed in the operator station is also included. • 1000 watt anti-freeze immersed heater with thermostat on PU-40 oil tank. • Continuous rotation through an 8 port hydraulic swivel and a 5 section electric swivel. OPTIONAL EQUIPMENT CYLINDERS - Rotobec built hydraulic cylinders, with bolt-on head, wear ring, and chrome plated tempered steel rod - Differs from each model - Attachment choice varies on application HYDRAULIC SYSTEM - Boom reach With M25 25’ (6.62 m) With MT26 Reach when extended: 25’6” (7.77m) Reach when retracted: 22’ (6.72 m) With MT27 Reach when extended: 27’ (8.23m) Reach when retracted: 23’6” (7.16 m) - Telescopic stick boom, activated by electric switch on joystick - Anchor kit - 42” Pedestal riser - Adjustable swing lock to set swing angle - Booms and attachment controlled by joysticks (for details on joysticks, valves and pumps, refer to specific model features/configuration - Operating pressure 3000 psi - Requires a double pump of 19.9/19.9 US gpm (75/75 lmp) at motor rpm - Standard heavy-duty spring loaded hydraulic accumulator protects the structure SWING SYSTEM - Powerful 345° limited rotation is standard - Continuous rotation is optional on most configurations - 26.45” (672 mm) outside diameter slewing ring - Rotation speed of 9.5 rpm with 19.9 US gpm ADDITIONAL TECHNICAL INFORMATION - Overturning moment: 150000 ft.lb ACCESSORIES - Refer to each specific model ROTOBEC ELITE SM 22 FEET RANGE/LIFT DIAGRAM Approximate lift capacity in pounds (less attachment) • Heavy-duty spring loaded hydraulic accumulator reliably protects the loader structure. Stationary loader with operator station and power unit on turret • Insulated cab (38” x 52”) with wiper, fan, roof light and 2 lights towards the front. • 4000 watts electric heater with thermostat and fan (not available with continuous rotation option). • Air conditioning (not available with continuous rotation option). • Cab front windshield protective grid. • Radio AM/FM/CD. • 50 feet extension cable for PU-40 and loader without continuous rotation. Connects PU-40 to the loader to feed cab and loader electric accessories. • 50 feet extension cable for PU-40 and loader with continuous rotation option. Connects PU-40 to the loader to feed cab and loader electric accessories. Also includes wires connecting the start/stop buttons to the PU-40. - Main boom: - Stick boom: DISTANCE ABOVE AND BELOW GROUND LEVEL IN FEET OPTIONAL EQUIPMENT STANDARD EQUIPMENT & ACCESSORIES • Electric junction box and a Danfoss (12 Volts) electric-over hydraulic proportional control valve assembly are factory installed at the base of the loader and protected by a hood. • Two electric joysticks and a safety cut-off switch are supplied to be dealer installed inside a remote operator station. • Two 50 feet electric cables to connect the joysticks to the Danfoss control valves are also supplied. Stationary loader with operator station but no power unit on turret STANDARD EQUIPMENT & ACCESSORIES Stationary loader for remote operation - Standard boom reach: 22’ (6.72 m) - Main boom length: 148” (3759 m) - Stick boom length: 122” (3099 mm) - Main boom structure: rectangular 6” X 8” (152 mm X 203 mm) high tensile steel - Stick boom structure: rectangular 6” X 6” (152 mm X 152 mm) high tensile steel - Booms design for closer access to the loader pedestal - Two 55 Watt halogen work lights; one on each side of the stick boom - Boom pivot points: 2” (50.8 mm) diameter induction tempered and chromed steel pins mounted on bronze bushings - Complete main boom cycle: 8.2 sec. with 19.9 gpm (75 lpm) - Complet stick boom cycle: 6.5 sec. with 19.9 gpm (75 lpm) Stationary loader for very short distance remote operation • An operator station is supplied for dealer installation within 15 feet from the loader. It includes the operator seat, the hydraulic control valve assembly mounted under the operator’s seat and 2 mechanical joysticks mounted on the valves. • PU-40 Power unit includes a 40 hp electric motor, an electric panel, a cut-off switch, a double gear pump, a thermostatic oil cooler, a 44 US gallon oil tank, a support structure and hood. • 1000 watt anti-freeze immersed heater with thermostat on PU-40 oil tank. • 1000 watt anti-freeze immersed heater with thermostat on PU-40 oil tank. • Continuous rotation through a high capacity sealed and insulated 4 section electric swivel. • Insulated cab (38” x 52”) with wiper, fan, roof light and 2 lights towards the front. • 4000 watts electric heater with thermostat and fan. • Air conditioning. • Cab front windshield protective grid. • Radio AM/FM/CD. • PU-40 power unit includes a 40 hp electric motor, an electric panel, a cut-off switch, a double gear pump, a thermostatic oil cooler, a 44 US gallon oil tank, a support structure and hood, non continuous rotation limited to 345 degrees, an operator station mounted on the turret and including the operator seat, the hydraulic control valve assembly mounted under the operator’s seat, 2 mechanical joysticks mounted on the valves and start/stop/accessories switches mounted close to the operator. The operator station is ready to receive an optional cab. OPTIONAL EQUIPMENT STANDARD EQUIPMENT & ACCESSORIES OPTION]AL EQUIPMENT STANDARD EQUIPMENT & ACCESSORIES ACCUMULATOR DISTANCE FROM CENTERLINE OF ROTATION IN FEET MAXIMUM MAIN BOOM LIFT CAPACITY REACH (FT) CAPACITY (LB) ELAVATION FROM GROUND (FT) * Capacity limited by stick boom. Standard Range/Lift Diagram • ELITE SM M22