THE LEADING FORCE behind liquids™ since 1857 A Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer

The Roper Pump Family of Gear Pumps ■ Industrial applications requiring a special mechanical seal ■ ANSI Flanges ■ Many parts interchangeable with 3600 Series ■ Direct drive or built-on gear reducers ■ Bi-directional rotation* ■ Congurations available for close coupled drive and close coupled hydraulic drive ■ Oilelds including light & heavy crude oil ■ Kerosene mixtures, condensates and hot oils ■ Sealed ball bearings ■ Quadruple grease purged lip seals ■ Helical gears for quiet operation ■ Bi-directional rotation* ■ Fuels, solvents, petrochemicals ■ Residual fuel oils, molasses, resins ■ Tankers,...

A Series General Purpose Pumps General Purpose Pumps for Pressure Lubrication, Hydraulic Service, Fuel Supply and General Transfer Up to 59 GPM Roper A Series pumps are adaptable to a wide range of applications pumping clean uids, such as pressure lubrication, hydraulic service, fuel supply or general liquid transfer. These pumps are designed to operate at standard motor speeds, with provisions for ange or foot mounting. The internal bearings are lubricated by the uid being pumped. With only two moving parts, the pumps run quietly. They are manufactured and assembled with close tolerances, and...

Capacities & Nomenclature SIZE 005 THROUGH 02 A SERIES NOMENCLATURE 1 - Foot Mounted 26 - Baseplate Mounted with Relief Valve 18 - Flange Mounted with Relief Valve 2 - Foot Mounted with Relief Valve 34 - Close Coupled with Relief Valve AL - Lip Seal Seal Option Flange Mounted AP - Packed Box AE - Mechanical Seal (AE Series Only) 005 - 0.05 Gal /100 Rev [0.19 L /100 Rev] With Mounting Bracket *Size: approximate theoretical ow rate [not including slip] Type 1 Internal Construction Type 1 Internal Construction MECHANICAL SEAL (POSITIVE DRIVEN) MECHANICAL SEAL (STANDARD) Mechanical seals are for...

Pump Seals SIZE 06 THROUGH 40 Flange Mounted Foot Mounted PACKED BOX The packed box seal is suited for general purpose applications. The standard packing has a temperature limit of 250ºF (121ºC), with special tting available for higher temperature applications. The gland should be adjusted to allow slight seepage. Foot Mounted Flange Mounted Baseplate Mounted Close Coupled to NEMA “C” Motor LIP SEAL The lip seal is suitable for low pressure sealing of lubricating uids. The standard seal has a temperature limit of 212ºF (100ºC). Special tting is available for higher temperature applications. Available...

A Series Performance Charts SIZE If there is any question concerning these charts or the recommended operating conditions, please consult your Roper distributor, district representative, or the home ofce. [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] [l/min] [kW] Performance gures show maximum horsepower requirements for minimum rated gallons per minute at the various speeds, viscosities and pressures. The charts are intended as a guide for conditions at the pump. In determining the proper conditions...

NOTE: Consult your Roper Area Sales Manager for operation in the ranges indicated by the yellow colored areas. NOTE: An outboard ball bearing is recommended for viscosities below 40 ssu.

A Series Dimensions SIZE 005 THROUGH 02 (ange mounted) THREE HOLES 1/4-20 UNC THREAD EQUALLY SPACED ON 2-3/4 DIA. B.C. SIZE 06 THROUGH 16 (foot mounted) PUMP 1-1/4 DIA. N.P.T. PORT EACH SIDE [32] SIZE 21 THROUGH 40 (foot mounted) PUMP S (N.P.T. PORT EACH SIDE) R (RELIEF VALVE) ROPER PUMPS - THE LEADING FORCE behind liquids™ since 1857

SIZE 003 (ange mounted) SIZE 003 (foot mounted) THREE HOLES 1/4-20 UNC THREAD EQUALLY SPACED ON 2-3/4 BIA. B.C. 1-9/16 [40] SIZE 06 THROUGH 16 (ange mounted) R (RELIEF VALVE) 7-1/2 DIA.[191] SIX HOLES 9/16 DIA.[14] EQUALLY SPACED ON 6-7/16 [164] DIA. BOLT CIRCLE 1-1/4 N.P.T. PORT EACH SIDE [32] SIZE 21 THROUGH 40 (ange mounted) PUMP S (N.P.T. PORT EACH SIDE) 1 DIA. [25.4] 3/16 [5] SIX HOLES 9/16 DIA.[14] EQUALLY SPACED ON 6-7/16 DIA.[164] BOLT CIRCLE

AE Series Pumps Low Pressure ● Capacities to 130 GPM Pressures to 300 PSI Roper AE Series pumps are well suited to applications where a compact and quiet unit is required, such as hydraulic lift applications. Bearings and wear-plates are special wear-resistant, high lead bronze. The pumping gears are accurately machined to run quietly and smoothly. SIZE Pump NOTE: Consult your local Roper Pump Company representative for operation in the range indicated by the yellow colored areas. ROPER PUMPS - THE LEADING FORCE behind liquids™ since 1857

AE Series Dimensions SIZE 19 THROUGH 29 (foot mounted) S(N.P.T. PORT EACH SIDE) R(RELIEF VALVE) SIZE 54 (foot mounted) 20-5/16 (RELIEF VALVE) [516] 18-5/8 (PLAIN) [473] SIZE 75 (foot mounted) 24-13/16 (RELIEF VALVE) [630]

THE LEADING FORCE behind liquids™ since 1857 Roper Pump Company is a global supplier of high quality positive displacement pumps, designed to handle a broad range of industrial applications. In addition to helical gear pumps and progressing cavity pumps, we design and develop numerous custom pumps for customers with unique and demanding applications. From a small pump company founded in 1857, Roper Pump Company has grown into a technological leader. With a large installed base, we have both the knowledge and experience to help you solve your most challenging pumping problems…and our strong global...