SUPRA SK
2Pages

{{requestButtons}}

Catalog excerpts

SUPRA SK - 1

D Spannen: Spannen: Sicherungsring in in Richtung ’’UNLOCK’’ drehen (1.) Futter Sicherungsring Richtung ’’UNLOCK’’ drehen (1.) Futter öffnen (2.) Das Werkzeug ganz einführen (3.) Haltering festöffnen (2.) Das Werkzeug ganz einführen (3.) Haltering festhalten und Werkzeug durch Drehen der Hülse spannen (4.). halten und Werkzeug durch Drehen der Hülse spannen (4.). Sicherungsring zum Aktivieren der Spannkraft-- Sicherung in in Sicherungsring zum Aktivieren der Spannkraft-- Sicherung Richtung “LOCK“ drehen (5.). Richtung “LOCK“ drehen (5.). Öffnen: Öffnen: Sicherungsring zum Lösen der Spannkraft-Sicherung in in RichSicherungsring zum Lösen der Spannkraft-Sicherung Richtung ’’UNLOCK’’ drehen (6.). tung ’’UNLOCK’’ drehen (6.). Öffnen normal: Öffnen normal: Haltering festhalten und Futter durch Drehen der Hülse lösen Haltering festhalten und Futter durch Drehen der Hülse lösen (7.). (7.). Öffnen bei starker Spannung: Öffnen bei starker Spannung: Kraftverstärkung durch Einsetzen eines Stiftes in in die Bohrung Kraftverstärkung durch Einsetzen eines Stiftes die Bohrung am Haltering (8.), sonst wie Öffnen normal am Haltering (8.), sonst wie Öffnen normal Achtung: Netzstecker ziehen Achtung: Netzstecker ziehen oder oder Anhalten des Futters mittels Gabelschlüssel anan den MaschiAnhalten des Futters mittels Gabelschlüssel den Maschinenspindel-Schlüsselflächen (9.), sonst wie Öffnen normal. nenspindel-Schlüsselflächen (9.), sonst wie Öffnen normal. Achtung: Netzstecker ziehen Achtung: Netzstecker ziehen Futter auf Spindel montieren: Futter auf Spindel montieren: Spindel stillsetzen oder mittels Gabelschlüssel anhalten und Spindel stillsetzen oder mittels Gabelschlüssel anhalten und Futter mit Anzugsmoment von mindestens 2525 Nm auf Spindel Futter mit Anzugsmoment von mindestens Nm auf Spindel aufschrauben. Kraftverstärkung durch Einsetzen eines Stiftes aufschrauben. Kraftverstärkung durch Einsetzen eines Stiftes in in die Bohrung am Halterung A. die Bohrung am Halterung A. Futter demontieren: Futter demontieren: Spindel stillsetzen oder mittels Gabelschlüssel anhalten. Spindel stillsetzen oder mittels Gabelschlüssel anhalten. Futter am Haltering umfassen und abschrauben. KraftverstärFutter am Haltering umfassen und abschrauben. Kraftverstärkung durch Einsetzen eines Stiftes in in die Bohrung am Haltekung durch Einsetzen eines Stiftes die Bohrung am Haltering A.A. ring Futter mit Kegelaufnahme: Futter mit Kegelaufnahme: Kegel und Spindel müssen fett- und staubfrei sein. Kegel und Spindel müssen fett- und staubfrei sein. A A Haltering, B B Sicherungsring, C C Hülse - - Haltering, - - Sicherungsring, - - Hülse Für Schlagbohrmaschinen Für Schlagbohrmaschinen Für Schlagbohrmaschinen For Percussion Drills For Percussion Drills For à à Percussion Pour PerceusesPercussion Drills Pour Perceuses Percussion Pour Perceuses à Percussion Per Trapani Elettrici a Percussione Per Trapani Elettrici a Percussione Per Trapani Elettrici a Percussione Para Taladradoras a Percusión Para Taladradoras a Percusión Til Para Taladradoras a Percusión Til Slagboremaskiner Slagboremaskiner Til Slagboremaskiner SUPRA SK SUPRA SK SUPRA SK RÖHM GmbH · Postfach 11 61 D-89565 Sontheim/Brenz Telefon 07325/16-0 · Fax 07325 16-492 GB Chucking: Chucking: Turn the lock collar in in the direction ’’UNLOCK’’ (= OPEN) Turn the lock collar the direction ’’UNLOCK’’ (= OPEN) (1.) Open the chuck (2.) Insert the tool asas far will gogo (3.) (1.) Open the chuck (2.) Insert the tool far it it will (3.) Hold retaining ring tight and clamp the tool byby turning the Hold retaining ring tight and clamp the tool turning the sleeve (4.). Turn the locking ring to to ”LOCK” to activate sleeve (4.). Turn the locking ring ”LOCK” to activate the clamping force lock (5.). the clamping force lock (5.). Unchucking: Unchucking: Turn the lock collar in in the direction ’’UNLOCK’’ (= OPEN) to Turn the lock collar the direction ’’UNLOCK’’ (= OPEN) to release the chucking force (6.). release the chucking force (6.). Normal opening: Normal opening: Grip the retaining ring and open the chuck byby turning the Grip the retaining ring and open the chuck turning the sleeve (7.). sleeve (7.). Opening a firm chuck: Opening a firm chuck: Apply greater force byby inserting pin into the hole provided Apply greater force inserting a a pin into the hole provided onon the lock collar (8.), otherwise same procedure as normal the lock collar (8.), otherwise same procedure as normal opening. opening. Caution: pull out the mains plug Caution: pull out the mains plug or or Hold the chuck using anan open-end spanner on the machine Hold the chuck using open-end spanner on the machine spindle key faces (9.), otherwise same procedure asas normal spindle key faces (9.), otherwise same procedure normal opening. opening. Caution: pull out the mains plug Caution: pull out the mains plug Mounting the chuck on the spindle: Mounting the chuck on the spindle: Stop the spindle or or hold byby means of an open-end spanner. Stop the spindle hold it it means of an open-end spanner. Screw the chuck onto the spindle applying a tightening torque Screw the chuck onto the spindle applying a tightening torque of of min. 25 Nm. To apply greater force, insert a pin into the min. 25 Nm. To apply a a greater force, insert a pin into the Removing the chuck: Removing the chuck: Stop the spindle or or hold byby means of an open-end spanner. Stop the spindle hold it it means of an open-end spanner. Grip the retaining ring and screw offoff the chuck. To apply a Grip the retaining ring and screw the chuck. To apply a greater force, insert a pin into the hole provided in in the retaigreater force, insert a pin into the hole provided the retaining ring A.A. ning ring Chucks with taper mount: Chucks with taper mount: Taper and spindle must bebe free from grease and dust. Taper and sp

Open the catalog to page 1

All RÖHM GmbH catalogs and technical brochures

  1. F-SENSO 2

    9 Pages

  2. SUPRA SK E

    2 Pages

  3. PRIMA-S / -M

    1 Pages

  4. THE DURO-A.

    2 Pages

  5. BOHRFUTTER

    44 Pages

  6. ZS-ZSU

    2 Pages

  7. MKS

    1 Pages

  8. SUPRA-SK E

    1 Pages

  9. Oil and Gas

    24 Pages

Archived catalogs