1-channel Temperature Controller with Built-in SSR (Actual size)

SSR and controller integrated into a compact temperature control box. SB1 Series able of direct connection to oad. ature control can be easily assembled and started by connecting a heater line and temperature sensors to the SB1. Wiring is handled with connectors to reduce wiring time. Temperature Controller Connector Jacket heater, etc Max.7A(*) SSR Connector Temp pera erature sensor Output (To heater) Data D a can be viewed on site by ussing the display and operation n ke or controlled remotely via keys loader communication port. ((*) Permissible load capacity may be less than 7A depending on...

Can be installed in a small space or onto a pipe. Safety design The SB1 can be supplied with pipe wrapping type, pipe hanging type, DIN-rail mounting type, or panel mounting type. Proper mounting can be attained according to the pipe configuration. < Load Power Shutoff Function + Fuse > This function disconnects internal load power with an internal relay. A fuse is incorporated inside the SB1 to protect the instrument from a load shortcircuit. Pipe hanging type Pipe wrapping type Banding and strapping (Optional) Jacket heater Jacket heater Load Power Shutoff Function Mounting bracket for Pipe...

Cold-junction temperature compensation error Sampling time Influence of external resistance Influence of lead resistance Input impedance PV bias Input digital filter Control method Setting range Additional function Thermocouple input K, J (JIS/IEC) : 0 to 800°C, 0 to 999°F Thermocouple input 0°C or more, Less than 500°C : ± (1.5°C [2.7°F] + 1 digit) 500°C or more : ± (0.3% of Reading + 1 digit) RTD input 0°C or more, Less than 200°C : ± (0.6°C [1.1°F] + 1 digit) 200°C or more : ± (0.3% of Reading + 1 digit) ±1°C [1.8°F] (23°C±2°C [73°F±3.6°F]) ±2°C [3.6°F] (-10 to 60°C [ 14 to 140°F]) 0.25sec...

External Dimensions (Panel mounting hole dimensions) Panel mounting type 48.5±0.2 • Space required between SB1 Allow 30 mm or more between the instruments for proper heat dissipation when mounting two or more SB1 controllers in parallel. When mounting the instruments vertically, allow 200 mm or more to have space for wiring to or from the connectors installed on the top and the bottom of the SB1. Recommended screw size : M3 size [Nominal length (L): 6 mm or more] DIN rail mounting type DIN Rail Mounting bracket Jacket heater Pipe hanging type Pipe Mounting bracket for Pipe hanging (Heat radiating...

Pipe hanging Type Pipe wrapping Type

Mounting bracket Accessories (Sold Separately) • Mounting brackets are not necessary when using panel mounting type. DIN rail mounting Type DIN rail mounting bracketSB1P-M03 Pipe wrapping Type Mounting bracket for Pipe wrapping < Manufactured by PANDUIT Corporation > Stainless steel banding and strapping : MLT6EH-LP (Extra heavy Width : 12.7 mm, Length : 594mm) Pipe hanging Type Mounting bracket for Pipe hanging # Connector and Tool for cable wiring Connector Power supply/ Event input/output/ • Manufactured by WAGO Corporation: 721-2107/037-000 < Manufactured by PANDUIT Corporation > Stainless...

Upperside Connector Configuration Power supply/Event input/output/ Communication connector(CN1) Maximum allowable current (power supply part) is 15 A. Power (Total current : Maximum 15A) Connector (Sold Separately)Model Code : SB1P-C02 • Wiring tool (Sold Separately)Model Code : SB1P-C1 Lowerside Pin Compatible cable diameter : 12 AWG (2.5 mm2 ) Stripping length: 9 to 10 mm • The pins of the same number at line A and line B of the Plug are connected internally. • Communication and Digital input (Event input) cannot be selected at the same time. • Manufactured by WAGO Corporation: 721-2107/037-000...