Tube connection systems made of plastic - 25 Pages

Add to MyDirectIndustry favorites
Tube connection systems made of plastic

Catalog excerpts

RK LightClamps Light load range ■ Right angle tube connector Hinge tube connector ■ Axially parallel tube connector Features: ■ Only one element per type (018 / 030 / □ 30) ■ Elements made of reinforced polyamide ■ Closed elements or half cups ■ Tube clamping of different diameters or sections due to a special bush system ■ Every bush form is worked with the needed tube diameter ■ Anti turning device for the bush former due to a lokation pin in the bush ■ Attractive design ■ Zinc plated screws ■ Compatibility to the BLOCAN® profile system Options: ■ Equipped with stainless steel screws for...

 Open the catalog to page 2

Right angle tube connector (Single-pcs and multi-pcs elements) Light Clamps Selection guide Introduction Table of contents - RK LightClamps Hinge tube connector (Single-pcs and multi-pcs elements) Solid Clamps (Single-pcs and multi-pcs elements) Robust Clamps Axially parallel tube connector Light Clamps

 Open the catalog to page 3

Version: Light Clamps (^}-j Single-piece elements 9 For faster and more economic assembly Multi-piece elements 9 For add-on assembly and upgrading Features: ■ Restistance against corrosion and agressive substances ■ Low dead load ■ Applicable e.g. in the food packaging industry ■ Two basic diameters can be flexibly adapted with reducing bushes delivery from stock Light Clamps Light load range | Plastic

 Open the catalog to page 4

Adhesion force F [KN] Bending moment Mb [Nm] Twisting moment Mv [Nm] Loads RK LightClamps Attention! The data in the chart do not ensure a guarantee of quality or a warrant characteristic of our products. These are nonbinding standard values which might be not reached in individual cases due to the temperature or surface finish of the clamping profile. Tightening torque max: Sizes: 10 - 18: 2,5 Nm Material data sheet available upon request. KVR-KU Bushes LP-KU LPZ-KU LW-KU LF-KU

 Open the catalog to page 5

Reducing bushes / -insert size You can choose the size of the insert you want to introduce into the clamping element between 10 and 25 mm. The basic size of the round tubular connections is either 18 or 30mm. For any other required diameter the corresponding reducing bush can be delivered. Should you work with square tubes, which offer a choice between 10 and 20 mm, reducing bushes are a necessity. Reducing bushes / -insert form Not only can you choose the diameter of the reducing bush you require, you also have the possibility to choose its form. All you need to do is to choose the tube...

 Open the catalog to page 6

Selection guide Introduction Round tube Solid Clamps Reducing bush for one pcs elements, for round or square tube . Light Clamps The variable reduction sleeve concept : The illustration shows an element of type KVR. This element is on the one side a closed element and on the other side a half-cup element. Light Clamps Profile or rectangular tube Robust Clamps Reducing inserts for multi elements, for round or square tubes

 Open the catalog to page 7

Right angle tube connector Axially parallel tube connector Hinge tube connector Light Clamps Light load range | Plastic

 Open the catalog to page 8

Selection guide Introduction Robust Clamps Solid Clamps Light Clamps Light Clamps

 Open the catalog to page 9

RK LightClamps – Cross clamps Order instruction: Purchase only in lot sizes and a multiple of that, see product table below Inserts and bushes for diameter/ cross- section changes see accessories page 48 Standard: equipped and preassembled with galvanised screws Clamping levers have to be ordered separately Delivery unassembled See table last column and page 49 On request: Stainless screws Light Clamps Clamping lever S Code No.

 Open the catalog to page 10

Cross clamp KV-KU [mm] Cross clamp KVR-KU [mm] Reduction of the diameter or cross section of the clamping with inserts and bushes possible Light Clamps

 Open the catalog to page 11

RK LightClamps – Angle-/Base clamps Order instruction: Purchase only in lot sizes and a multiple of that, see product table below Inserts and bushes for diameter/ cross- section changes see accessories page 48 Standard: equipped and preassembled with galvanised screws Clamping levers have to be ordered separately Delivery unassembled See table last column and page 49 On request: Stainless screws Light Clamps Clamping lever S Code No. Angle clamps WV-KU Clamping lever S Code No. Light load

 Open the catalog to page 12

* Dimension of K are turned by 90° with a distance of 38-40 mm (slotted hole) Base clamps FS -KU Code No. K30018ACSR18 K30118ACSR18 K30030ACSR30 Clamping Type lot sizes A Base clamps FV-KU K30530ACSV30 Clamping lever S Code No. 93024 93024 902381 Reduction of the diameter or cross section of the clamping with inserts and bushes possible Light Clamps

 Open the catalog to page 13

RK LightClamps – Sleeve-/Flange clamps Order instruction: Purchase only in lot sizes and a multiple of that, see product table below Inserts and bushes for diameter/ cross- section changes see accessories page 48 Standard: equipped and preassembled with galvanised screws Clamping levers have to be ordered separately Delivery unassembled See table last column and page 49 On request: Stainless screws Light Clamps Clamping lever S Code No.

 Open the catalog to page 14

Flange clamp FK-KU [mm] Code No. Type lot sizes Flange clamp FKV-KU [mm] Reduction of the diameter or cross section of the clamping with inserts and bushes possible Light Clamps

 Open the catalog to page 15

■ Purchase only in lot sizes and a multiple of that, see product table below ■ Inserts and bushes for diameter/ crosssection changes see accessories page 48 ■ Standard: equipped and preassembled with galvanised screws ■ Clamping levers have to be ordered separately Delivery unassembled See table last column and page 49 Flange clamp V-KU Code No. Light Clamps Light load range | Plastic

 Open the catalog to page 16

Strap clamp LP-KU Weight Clamping lever S m [g] Code No. Strap clamp LPZ-KU Weight Clamping lever S m [g] Code No. Reduction of the diameter or cross section of the clamping with inserts and bushes possible

 Open the catalog to page 17

■ Purchase only in lot sizes and a multiple of that, see product table below ■ Inserts and bushes for diameter/ crosssection changes see accessories page 48 ■ Standard: equipped and preassembled with galvanised screws ■ Clamping levers have to be ordered separately Delivery unassembled See table last column and page 49 Strap clamp LW-KU Strap clamp LF-KU Code No. Type lot sizes DIN985 ** For Type 12-18, only 2 bores (centered) available. Light Clamps Light load range | Plastic

 Open the catalog to page 18

All RK Rose+Krieger GmbH catalogs and technical brochures

  1. RK LightUnit

    16 Pages

Archived catalogs

  1. Product overview

    24 Pages

  2. Profile Technology

    471 Pages

  3. Product overview

    57 Pages