ITAS - Industrial stairs and working platforms
31Pages

...no drilling or welding, no mitre cut - just assemble. Clamping set including clamping screw, clamping rocker, thrust pad and screw cap Internal tension system Principle: The clamping rocker is titled by screwing in the set screw. The other side of the clamping rocker pushes the pressure piece against the inner side of the tube. Without the need for any mechanical machining, the tube construction is positively and quickly connected by simply tightening a screw. Quick change system Working and machining areas which in the past required additional guards can now be made accessible with just...

Basic information / mechanical properties ■ ITAS die-cast elements ■ clamping mechanism inside from steel (zinc plated) Adh. force: static pull, dynamic pull+presure Industrial stairs and working platforms

ITAS - Load data ■ Load data according to DIN EN 1991-1-1:2010-12 ■ Maximum permitted load of steps (for a length of 1,2 m) 1500 N ■ Maximum permitted load of stairs cross beams (for a 45° angle and a length of 4 m without support) 3500 N ■ Maximum permitted load of railing (distance between pillars 0,7 m) 500 Nm ■ The maximum permitted load of the platform depends on the base construction. It cannot exceed the maximum permitted load of the base clamps used. ■ Technical safety requirements in accordance with DIN EN ISO 14122 part 1-4 ■ The railing must have at least one knee rail ■ Do not...

Features: ■ Technically optimised solution for the installation of railings, frame structures, boundaries, superstructures, stairs and working platforms of all kinds. ■ The smooth transitions between all of the elements used and the connecting tube are kind on the hands ■ Positive, quick connection with the simple tightening of a screw - without the need for any mechanical machining Internal tension system

Selection guide Introduction Robust Clamps Solid Clamps Light Clamps

■ ITAS elements in various RAL colours 232 ITAS Internal tension system

Corner T-joint WITE 40

■ ITAS elements in various RAL colours 234 ITAS Internal tension system

Cross horizontal KI 40H-45° Code No.

Internal tension system

Stair railing support TGHF

■ ITAS elements in various RAL colours Illustration shows right hand version Attenstion: please read the instruction manual TSI 40-WI Code No. Attentsion: please read the instruction manual238 ITAS Internal tension system

Crossovers made from ITAS elements provide access to various production areas. Robust Clamps Solid Clamps Light Clamps Selection guide Introduction

ITAS – Quick change system Quick & easy disassembly of rail parts in case of technical failures. Features: The new ITAS Quick change This system combines the pro- ven flexibility of the internal tension system and an easy assembly and dismantling system which cannot be compared to that of common railing systems. It enables protected working and machine areas to be more accessible. system permits an easy access to specific machine parts in case of technical malfunctioning: all you need is to remove the necessary part of the balustrade. Industrial stairs and working plat

Light Clamps Selection guide Introduction WIT 40-SW1 Robust Clamps Solid Clamps Release stopper with a screwdriver Loosen clamping screw Turn the cross strut to 90° and then raise and release Dismantling of quick change system

■ ITAS elements in various RAL colours 242 ITAS Industrial stairs and working platforms

■ ITAS elements in various RAL colours 244 ITAS Industrial stairs and working platforms

The mobile ITAS ladder makes accessing various storage shelves easier. Solid Clamps Light Clamps Selection guide Introduction

ITAS – Accessories Angle plate TGHF Side plate Surface element support FEH-l 40 Stair cross beam profile Stair joint Step profile Stair corner joint Industrial stairs and working platforms

Material: AlMgSi 0,5 F22 / EN AW 6060 Resistance moment W= 3 cm3 Moment of inertia I = 6 cm4 Aluminium tube Code No. fUiRK ROSE+KRIEGER Features: ■ The surface element support enables the clamping of panels of 4, 6 or 8 mm thickness. ■ The support can be used with a 040 tube (min. wall thickness 3 mm) ■ Only a 4.5 mm hole has to be bored into the tube where the support is then fixed with a thread former screw. Material: PA-GF, black Fixation set galvanized

■ ITAS elements in various RAL colours ITAS - Accessories ■ The angle plate is fixed to the corner of the stair cross beam at 90° degrees. Industrial stairs and working platforms

Features: ■ The 'T'-slot channels of the extruded aluminium profile enable fitting of the fixing components for the step profile (see p. 250). ■ The geometry of the 'T'-slot channels is designed to comply with the BLOCAN® Profile Assembly System which is designed and manufactured by RK Rose+Krieger. ■ Threaded holes ensure that the stair joints (see p. 252) can be fixed with set screws quality 8.8 ■ Realisation of 38, 45 and 60 degree leadangles without mitre cuts of the beam profile by using special designed stair joints. Saws with a smaller disc dia can therefore be used. ■ The geometry...

Material: AlMgSi 0,5 F22, natural Ix = 16 cm4 ly = 1003 cm4 Wx = 7 cm3 Wy = 80 cm3 Step profile Code No. Features: ■ An endless step profile made of extruded aluminium which is cut to the step width desired. ■ All stairs with a gradient angle of between 30 and 40 degrees are in accordance with standard DIN EN ISO 144122-:2016-10. This includes treads, height, overlap and width. They are also compliant with UVV (workers safety regulations and accident prevention rules). ■ Threaded channels have been prepared to ensure thar side plates can be fixed with standard M8 screws see p. 251). ■ This...

Features: ■ The code n° contains a complete fixing set for the fitting of the side plate to the step profile (see p. 250). ■ The arrangment of the holes and slots enables alignment of the step when it is fitted to the stair cross beam profile. The side plate serves as an end piece to the step width chosen by the customer. Material: AlMgSi 0,5 F22, natural Thickness t = 5 mm Site plate Code No.