Model RHSM-2A Dynamic HTHP Linear SwellMeter Instruction Manual Quality is Everything... Tel: 86-579-87537698(switchboard) URL: http://www.rigchina.com, Email: [email protected] MSN:[email protected] Address: No.80-82, Qiude Rd,west Cheng Industrial Eastate,Yongkang,Zhejiang Province, China

1. Outline………………………………………………………………………….………….3 2. Equipment Technical Parameters …...………………………………………3 3. Equipment Working Principle and Structure ………………….…….…3 4. Testing Steps…………………………………………………………………….………6 5. Equipment Maintenance and Notes.……………………………….………6 6. One-Year Spare Parts (Optional)………...…………………….….………7 II CHAPTER SOFT WARE 7. Install & Uninstall………………………………………………………….………….8 8. Instruction Steps ……………………………………………………….………….17 Please carefully read the MANUAL to command installation and use of the product. After reading, keep this manual for future checking, mending and maintenance....

ⅠOutline High temperature & high pressure intelligent shale dilatometer is able to test the hydrous swelling property under good analog downhole temperatures and pressure differences. This supplies an advanced testing method for stability research and evaluation of oil field borehole walls and selection of compounding of anti-caving drilling fluids. RHSM-2A shale dilatometer collects data with a computer, which improves data accuracy, makes performance more stable, enlarges its measuring range, and leaves no drifting. It can be used at high temperatures, high pressures and also can be used at...

expansion curve will be made out. (2) Structure (see picture 1) (3) Equipment components: heating body, main testing cup, device for relieving of high pressure, computer, software, printer, and main testing cup base. Sensor Chamber Assistant Handle Cross Valve Sealing Ring Communication Valve Stem Cross Valve Liquid Cup Cover Liquid Cup Drill Core Cup Drill Core Case Support Block Liquid Injection Valve Communication Valve Stem (Picture 1) Ⅳ. Testing Steps Note: Sensors and Position moving testing part of the main testing cup have been calibrated by manufacturers. Please do not make dissembling...

2. Place the baked sample soil to be tested into the drill core case, and pat it lightly to make it flat. Then, put a piece of 1 inch filter paper onto the sample soil, lightly turn the drill core press rod into the drill core case, and press the rod with hands for a solid status. Then, operate the pressure machine for more than 5 minutes of 14 MPa pressing. Finally, take it down. 3. Lightly turn the drill core press rod and lift it out, and the sample is well made. Place the drill core case components into the testing cup body (Note: Before this, check if the φ55×3.1 O ring has been placed into)....

pressure rubber pipes at the manifold with the connection screw nuts of cross valves at the main testing cup and liquid injection cup and tighten up. At this time, the pressure handle at the high pressure manifold should be at a free status. 7. Plug the thermocouple into the heat sensing hole, check if the sensor signal line is well connected, and lightly press the assistant button at edge of the sensor case with a hand to make the tested drill core contacted well with the testing plate. 8. Inject 2 MPa pressure into the liquid cup, and start to heat to the demanded temperature. 9. When reaching...

10.8 Loosen the fastening screws at the lower end of the cup body and take out drill core case components. 10.9 Wash each part of the cup body. When washing the testing plate, use a nipper to get a little of cotton to clean it with alcohol and keep it dry after washing. Ⅴ. Equipment Maintenance and Notes 1. On many times of testing, regularly check if O rings at both upper and lower ends of the main testing cup are deformed or broken. 2. When the equipment is after use, bake the parts apt to rust such as communication valve stems, hexagon socket set screws with cone points, and paint grease onto...

Soft Ware Install & Uninstall • PC: desktop calculating , notebook; • Operating system: Windows 9X/NT/2000/XP/2003; • Drive: CD-ROM; • Printer: Applicable to any printer, A4 print paper; • Other Equipment: mouse, ; 1) Click "setup.exe" to start the installation. Sr LINEAR HTHP SWELL METER SOFT WARE File: Edit View Favorites Tools Help E3 ]\LINEAR HTHP SWELL METER SOFT WARE v 0Go Q - ffi JD Search Installer Package 2) Install .NET Framawork2. 0 takes time (.NET Framawork2. 0 is the HTHP linear meter system working environment. In the case of "Do you accept the terms of the pending License Agreement?"...

Rjgchjnq CROUP HTHP I.1NHAK METER STSTEI Setup Crystal Reports Basic for Visual Studio 2008 (x8G. xG4] Please read the following license agreement. Press the page down key to see the rest CRYSTAL REPORTS BASIC FOR MICROSOFT VISUAL STUDIO 2008 LICENSE AGREEMENT IMPORTANT READ CAREFULLY: THIS IS A LEGAL AGREEMENT BETWEEN YOU AND BUSINESS OBJECTS SOFTWARE LIMITED ("BUSINESS OBJECTS") FOR THE BUSINESS OBJECTS SOFTWARE PRODUCT IDENTIFIED ABOVE. WHICH MAY INCLUDE COMPUTER SOFTWARE. ASSOCIATED MEDIA. PRINTED MATERIALS AND ONLINE OR ELECTRONIC DOCUMENTATION ("SOFTWARE"). BEFORE CONTINUING WITH THE INSTALLATION...