Catalogs >
RIGCHINA GROUP COMPANY >
MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids
1 / 8Pages

Catalog excerpts

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 1

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES 2-SCALE STAINLESS STEEL MUD BALANCE Complete with Case Model RCMB Series Instruction Manual

Open the catalog to page 1

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 2

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES ©2014 Rigchina Group Company All rights reserved. No part of this work covered by the copyright hereon may be reproduced or copied in any form or by any means (graphic, electronic, or mechanical) without first receiving the written permission of Rigchina Group Company 2

Open the catalog to page 2

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 3

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES 1. Introduction The Rigchina Two-Scale Mud Balance is an accurate, self-contained measuring device used to determine the density of drilling fluid. The Model RCMB-7 (Part No. 115-7) has a range of 0.8 to 13 pounds per gallon or Specific Gravity of 0.1 to 1.5. The Model RCMB-4 (Part No. 115-4) has a range of 0.58 to 24 pounds per gallon or Specific Gravity of 0.7 to 2.9. The density or weight of a given volume of liquid is determined by using a mud balance. The Mud Balance consists of a constant-volume balance cup and lid connected to a...

Open the catalog to page 3

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 4

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES 2. Procedure 1. Place the mud balance base on a flat level surface. 2. The balance cup should be clean and dry before it is filled with the drilling fluid sample. 3. Measure the temperature of the fluid and record on the appropriate mud report form. 4. Fill the balance cup with the sample to be tested. Tap the side of the balance cup several times to break up any entrained air or gases. Put the lid onto the balance cup by pushing it downward with a slow rotating motion until it is firmly seated. Be sure that some mud is expelled through...

Open the catalog to page 4

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 5

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES

Open the catalog to page 5

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 6

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES

Open the catalog to page 6

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 7

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES Name Sample cup Cup cover Screw, M4×20 Screw, M2×12 Brand Screw, M2×12 Level Bubble Screw, M3×16 Knife edge Fulcrum Cylinder screw, M4×35 Nut, M4 Spacer, d=4 Supporting base Main scale bracket Main scale Weights Scale beam Screw, M4×16 Cover screw Balanced tube Lead shot Locating screw Set screw

Open the catalog to page 7

MUD BALANCE | RCMB series | measure the density of drilling fluids and other fluids - 8

DRILLNG FLUIDS & OIL WELL TESTING MUD BALANCE SERIES 5. Warranty and Returns 5.1 Warranty Rigchina Group Company warrants its products to be free from defects in material and workmanship for a period of 12 months from the time of shipment. If repair or adjustment is necessary, and has not been the result of abuse or misuse within the twelve-month period, please return, freight prepaid, and correction of the defect will be made without charge. Out of warranty products will be repaired for a nominal charge. Please refer to the accompanying warranty statement enclosed with the product. 5.2...

Open the catalog to page 8