WHEEL CENTER BORE INNER DIAMETER MEASURING GAUGE RF096-50/70-200-Clb Series User's manual www.riftek.com [email protected]

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Safety precautions · Use supply voltage and interfaces indicated in the system specifications. · In connection/disconnection of cables, the system power must be switched off. · Do not use the system in locations close to powerful light sources. The system has been developed for use in industry and meets the requirements of the following Directives: · EU directive 2014/30/EU. Electromagnetic compatibility (EMC). · EU directive 2011/65/EU, “RoHS“ category 9. Laser safety The system makes use of a c.w. 660 nm wavelength...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Basic technical data Parameter Diameter measurement range, mm Space resolution, points/turnover Measurement accuracy, um Depth of measurement, mm Measurement cycle (no more), s Light source Output power, mW Laser safety class Output interface Power supply, V Power consumption, W Environmental resistance Vibration Shock Permissible ambient light, lx Relative humidity, % Operating ambient temperature, °С Storage temperature, °С Housing material Weight (without cable), gram Value 50...70 3200 ±5 200 20 red semiconductor...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Structure and operational principle Operation of the system is based on the item surface scanning by rotating laser triangulation sensors. To get required accuracy for the whole measurement range the measuring gauge contains two laser sensors inside one measuring head. The measuring head is mounted on rotational module. The system also contains a calibration ring placed with the possibility of linear translation along the measuring head. In the initial state, the calibration ring is located at the level of the laser...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Connection Designation of connector contacts View from the side of connector contacts used in the system: 6 Connector Binder 712 Series, #99-0426-10-08 Designation of contacts is given in the table below: Pin number 1 2 3 4 5 Assignment #99-0426-10-08 A (input) GND 5V (output) B (input) Z (input) Cable Designation of cable wires is given in the table below: Pin number Binder Binder Binder Binder Binder free lead free lead free lead Assignment #99-0426-10-08 A (input) GND 5V (output) B (input) Z (input) No connection...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Visual inspection · · · · Check the system for completeness and absence of damage. Check the cables and ground wire. Check the condition of output windows and, if necessary, clean them. Rotate the measuring head by hand to check smooth progress. The system is positioned so that the object under control has to be placed within the working range of the system and on the laser beam axis. The measurement process is fully automated and operation of the system is reduced to the work with the software. Service software General...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series RF096 Test Program Connection When you run the program, parameter fields (Device IP Address, Remote Port, Local Port) are populated with factory defaults. If you didn't change the system parameters, you can click the Connect button. Otherwise, change factory defaults to the actual system parameters and then click Connect. When the connection is established, the system information will be displayed. It is necessary to calibrate the system before you start the measurement process. Make sure that the calibration ring is...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series When the system is calibrated, it's ready to operate. Click the Measure button in order to start the measurement process. The program will display the calculated values of diameter and roundness, profile points (in green) and average diameter circle (in blue) on the widget below.

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series You may turn on and off a scale grid by clicking the Grid button. When the Auto button is pressed, you cannot zoom and move the image. You may zoom in and out (by mouse wheel) and move the image (by pressing the left mouse key and moving a cursor), when the Auto button is unpressed (shown in gray). Warranty policy Warranty assurance for the Wheel Center Bore Inner Diameter Measuring Gauge RF096-50/70-200-Clb Series - 24 months from the date of putting in operation; warranty shelf-life - 12 months. Revision 1.0.0 Starting...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Beijing Gemston Mechanical & Electrical Equipment Co., Ltd Xi'an Win-Success Automation Technology Co.,Ltd RAILWAY INSTRUMENTS ONLY Room 613, Anfu Mansion, Fengtai District, Beijing, China Tel: +86 10 6765 0516 Fax: +86 10 6765 6966 Mobile: +86 137 1755 1423 [email protected] www.baoft.cn Room 3-1-1039, Iduhui Building, No.11 Tangyan South Road High-Tech Zone, Xi’an Shaanxi PRC, China Tel: +86 29 81106280 Fax: +86 29 81106285 Mob: +86 133 19271405 [email protected] www.maxsensor.com CZECH REPUBLIC Rm 2205-2210, Zhongyou...

Wheel Center Bore Inner Diameter Measuring Gauge. RF096-50/70-200-Clb Series Influx Big Data Solutions Pvt Ltd Paragon Instrumentation Engineers Pvt. Ltd. PT. DHAYA BASWARA SANIYASA No:2, Krishvi, Ground Floor, Old Airport Road, Domlur, Bangalore - 560071, India Tel: +91 73 37748490 Tel: +91 94 48492380 RAILWAY INSTRUMENTS ONLY 200, Station Road, Roorkee, 247 667, India Tel: +91 1332 272394 [email protected] www.paragoninstruments.com Botanic Junction Blok H-9 NO. 7 Mega Kebon Jeruk, Joglo Jakarta,11640, Indonesia Tel: +62 21 2932 5859 [email protected] Nisso Dekalo Import Export...