HANDHELD INNER DIAMETER MEASURING GAUGE RF096-18/30-155/307-HH Series User's manual www.riftek.com [email protected]

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Safety precautions and measurement conditions · When installing the gauge into the channel, avoid distortions and strong impacts. · It is necessary to periodically inspect the windows of the laser sensor and clean them of dirt. The gauge has been developed for use in industry and meet the requirements of the following Directives: · EU directive 2014/30/EU. Electromagnetic compatibility (EMC). · EU directive 2011/65/EU, “RoHS“ category 9. Laser safety The gauge makes use of an c.w. 660 nm wavelength semiconductor laser. The...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Basic technical data Parameter ID measurement range, mm ID measurement error, mm Discreteness of indication, mm Space resolution, points/turnover Measurement depth from the pipe end, mm Measurement time, not greater, s Measured parameters Value 18...30 ±0.05 0.01 700 155...307 2 diameters (min, max, average), ovality, roundness see Figure 4 Dimensions Power supply, V Number of measurements before recharging, not less Operating ambient temperature, °С Enclosure rating Laser sensor output power, mW Laser safety class Weight,...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Device structure Basic components Figure 2 shows the main components of the gauge: Designations: (1) Laser scanning module (2) Guide bush with nut (3) Calibration module (4) Charger (5) Data cable

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Laser scanning module Figure 3 shows the main components of the laser scanning module: Designations: (1) Power button (2) Measurement button (3) Display (4) Charger connector (5) Guide shaft with a scale (6) Rotating laser head (7) Scale on a guide bush

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Overall dimensions of the laser scanning module are shown in Figure 4: Calibration module The module is designed to calibrate the gauge and check its performance. The overall dimensions of the module and the nut are shown in Figure 5:

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Operating principle The operation of the gauge is based on the principle of laser scanning of the inner surface of the pipe by a rotating laser head. The rotation of the laser head is carried out by a built-in motor. The gauge is equipped with a display for showing the result. The gauge operates as follows: the guide bush 2 (Figure 2) is installed at the end of the controlled hole by using a nut. The operator inserts the laser head into the pipe through the guide bush at a predetermined depth, which is counted on a scale marked...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Basic settings Before you start working with the device, it is necessary to configure its basic parameters. In the main program window (see p. 10), tap the Device button: 9 Button Date/Time Language Synchronization Database Measure type Assignment Date/time settings. Program language selection. Synchronization with PC. Database settings. Measurement type selection (rapid measurement or measurement according to the scheme). Date/time settings To set the date and time, tap the Date/Time button. Then use the buttons to set the...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series To transfer data between PDA and PC, it is necessary to synchronize them. There are two ways of synchronization via USB cable. When you select MS ActiveSync, synchronization with PC is performed via the ActiveSync software (Windows XP), or via Windows Mobile Device Center (Windows 7). When you select Mass Storage, the device is detected in Windows as an external storage device. To select the type of synchronization, tap the Synchronization button in the Device window. Then select the required type and tap Save. For the changes...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series To create a new database, tap the Add button. The window for entering a name of the new database will appear. By default, it will be prompted to form the database file with the name db_yy_mm_dd.idt, where yy_mm_dd is the current date: yy – the last two digits of the year; mm – month; dd – day. You can agree with this name, or enter another: After typing the name, tap the Enter button - To select the database from a list, tap on the line and then tap Select. The selected file will be marked with a "dot" symbol. To delete the...

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Calibration and measurement settings To configure calibration and measurement settings, tap the Settings button in the main program window. 12 To make changes, you need to select the required parameter and enter the new value in the Data Input window. Then tap the Enter button - To save the changes, tap the Save button. Description of parameters: Parameter Calibration diameter Calibration tolerance Inner diameter Outer diameter Measurement tolerance Description Calibration ring diameter. Tolerance for calibration and testing....

Handheld Inner Diameter Measuring Gauge. RF096-18/30-155/307-HH Series Parameter Reference D Reference T Measured D Measured T Description Calibration ring diameter. Tolerance for calibration and testing. Measured diameter. Deviation from the reference value. · Tap the Calibration button. The gauge will scan the calibration ring and perform an automatic calibration. Then the gauge will scan the calibration ring again in order to perform the testing procedure. If successful, you will see the following message: The Measured T column shows the difference between the actual value of the ring diameter...