*mydirectindustry

Catalogs
RHEINTACHO Messtechnik GmbH
Sensor: Differential-Hall high pressure M12 series

Sensor: Differential-Hall high pressure M12 series

Product catalog summary

Overview: The document is a technical data sheet for the 1-Channel Differential-Hall M12 high-pressure series speed sensor by RHEINTACHO Messtechnik GmbH, designed for high-pressure applications in vehicles, mobile machines, and hydraulic drives.

Specifications:

Power Supply: 11 VDC to 30 VDC
Frequency Range: 0.5 Hz to 20 kHz
Operating Temperature: -40°C to +125°C (-40°F to +257°F)
Degree of Protection: IP67, IP69K
Pressure Resistance: 500 bar static, 225 bar dynamic

Features:

High pressure resistance
Detection up to 20,000 Hz
Large air gap
Stainless steel housing

Mounting Instructions:

DIN type thread with ISO 6149 sealing system
Tightening torque: 25 Nm
Careful handling to prevent damage to the sensor face and seal

Electrical Specifications:

Current Consumption: 20mA at 24 VDC, 1000Hz
Max Output Current: 500 mA at 24 VDC, 100 mA at 30 VDC
Short Circuit and Reverse Polarity Protection

Environmental Conditions:

Vibration Resistance: 10 Hz to 1000 Hz
Shock Resistance: 100 g at 6 ms
MTTF: 150 years at +100°C

Safety Instructions:

Installation and commissioning should be done by trained specialists
Ensure the system is safe before commissioning
Do not use defective components

Transport and Storage:

Inspect for transport damage
Do not use if dropped

Connection Guidelines:

Use short, shielded cables
Avoid proximity to large electrical machines

Wiring and Connection Guidelines: Wires should ideally be routed inside the vehicle. If external routing is necessary, ensure secure attachment. Avoid kinks, twists, and unprotected routing through sharp edges. Shield lines to speed sensors, keep them short, and connect the shield to electronics or vehicle ground. Avoid routing near power-conducting lines and secure the cable harness near the sensor.

Intended Use: The speed sensor must operate within specified voltage, temperature, vibration, and shock ranges. Use outside these conditions can be hazardous and cause damage.

Improper Use: Using the sensor outside the intended use, especially in explosive areas, is prohibited. Such misuse voids warranty and liability claims.

Safety-Related Functions: Customers must conduct risk analysis and implement safety measures like redundancy and emergency switches. Necessary product data for safety assessment is available upon request.

Disposal: Dispose of the speed sensor according to national regulations.

Technical Changes: Technical changes may occur without notice. Liability for errors is excluded.

Catalog excerpts

Sensor: Differential-Hall high pressure M12 series-1

Drehzahlen sicher erfassen, anzeigen und kontrollieren For reliable measurement, control and indication of rotational speeds M12hp Technisches Datenblatt / Technical Data Sheet Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12 Hochdruck Baureihe / 1-Channel Differential-Hall M12 high pressure series Für Hochdruckanwendungen geeignet Suitable for high pressure applications RHEINTACHO Messtechnik GmbH · Waltershofener Str. 1 · D-79111 Freiburg phone +49 761 4513 0 · fax +49 761 445274 · www.rheintacho.de

Open the catalog to page 1

Sensor: Differential-Hall high pressure M12 series-2

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Kurzdaten Versorgung Data summary Power supply Frequency range Drehzahlerfassung an Zahnrädern mit kleinem Modul und hoher Auflösung Speed detection of gearwheels with small module and high resolution Anwendung in Fahrzeugen, mobilen Arbeitsmaschinen und hydraulischen Antrieben Applications in vehicles, mobile operating machines and in hydraulic drives Hohe Druckfestigkeit High pressure resistance Großer Schalabstand Richtungsabhängiger Einbau...

Open the catalog to page 2

Sensor: Differential-Hall high pressure M12 series-3

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Gehäuse / Housing Gewinde / Thread Stecker / Plug Ausgang / Output Anschluss / Connection PNP 2 m Kabel ohne Stecker / 2 m cable without plug 5,5 m Kabel ohne Stecker / 5.5 m cable without plug ohne Kabel, mit Stecker / without cable, with plug am Sensor montierter 4-poliger Binder-Stecker, M12 (männliche Ausführung) / 4 pin Binder plug mounted on the sensor, M12 (male type) ohne Stecker / without plug Lieferumfang / Scope of delivery Sensor,...

Open the catalog to page 3

Sensor: Differential-Hall high pressure M12 series-4

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Einbau / Mounting Einbauart / Mounting principle Anzugsmoment / Tightening torque Schalt- / Einbauabstand / Air gap Einschraubgewinde, richtungsabhängig mit Dichtungssystem nach ISO 6149 / DIN type thread, direction related mounting with sealing system according to ISO 6149 25 Nm Modul / module 1: Modul / module 1,25: Modul / module 1,5: Modul / module 2: Modul / module 3: Modul / module 4: Maximaler Einbauabstand bezogen auf Modul und Arbeitsfrequenz...

Open the catalog to page 4

Sensor: Differential-Hall high pressure M12 series-5

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Elektrische Daten / Electrical Specifications Versorgung / Power supply Stromaufnahme / Current consumption Anschlussschaltbild (PNP/NPN) / Electrical connection (PNP/NPN) Frequenzbereich / Frequency range Max. Ausgangsstrom / Max. output current 500 mA @ 24 VDC, 25°C, 50 % Einschaltdauer (duty cycle); 100 mA @ 30 VDC, 100°C, 50 % Einschaltdauer (duty cycle) Kurzschlussfest / Short circuit immunity Gegen alle Leiter / against all terminals...

Open the catalog to page 5

Sensor: Differential-Hall high pressure M12 series-6

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Einsatzbedingungen / Environmental conditions Betriebstemperaturbereich, Sensor / Operating temperature range, sensor Druckfestigkeit der Messfläche / Max. pressure on sensing surface 500 bar @ statischer Druck (static pressure) 225 bar @ dynamischer Druck (dynamic pressure) Vibration / Resistance SDP15.GI05.E2R, SDP15.GI05.E55R: IP67 SDN2.GI03.SBR, SDP2.GI03.SBR: IP69K Rauschen: 10 Hz ...1000 Hz (10 Hz 0.093 g2, 18 Hz 0.093 g2, 1000 Hz 0.043...

Open the catalog to page 6

Sensor: Differential-Hall high pressure M12 series-7

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Zeichnungen / Drawings Datumscode (Datecode) RHEINTACHO Messtechnik GmbH · Waltershofener Str. 1 · D-79111 Freiburg phone +49 761 4513 0 · fax +49 761 445274 · www.rheintacho.de

Open the catalog to page 7

Sensor: Differential-Hall high pressure M12 series-8

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Zeichnungen / Drawings Datecode JJWWXX RHEINTACHO Messtechnik GmbH · Waltershofener Str. 1 · D-79111 Freiburg phone +49 761 4513 0 · fax +49 761 445274 · www.rheintacho.de

Open the catalog to page 8

Sensor: Differential-Hall high pressure M12 series-9

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Sicherheitshinweise / Safety Instructions Allgemeine Hinweise General instructions Vor Festlegung Ihrer Konstruktion verbindliche Einbauzeichnung Before finalizing your design request a certified installation drawing. Any suggested circuits do not imply any technical liability for the system on Eventuelle Schaltungsvorschläge beinhalten keinerlei system- technische Verantwortung für die Anlage. Öffnen des Drehzahlsensors, Änderungen bzw....

Open the catalog to page 9

Sensor: Differential-Hall high pressure M12 series-10

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Hinweise zur Beschaltung und Leitungsführung Notes regarding the connection and the wiring Leitungen zu den Drehzahlsensoren sind so kurz wie möglich und Lines to the speed sensors are to be shielded and kept as short as possible geschirmt auszuführen. Die Abschirmung ist einseitig an der Elektronik oder niederohmig an der Geräte- bzw. Fahrzeugmasse anzuschließen. Der Drehzahlsensor sollte nur im spannungslosen Zustand gesteckt Die Sensorleitungen...

Open the catalog to page 10

Sensor: Differential-Hall high pressure M12 series-11

Drehzahlsensor / Speed Sensor 1-Kanal Hall-Differenz M12hp Baureihe / 1-Channel Differential-Hall M12hp series Technisches Datenblatt / Technical Data Sheet Einsatz in sicherheitsrelevanten Funktionen Es ist die Verantwortung des Kunden, eine Risikoanalyse seines The customer is responsible for performing risk analysis on the entire Gesamtsystems durchzuführen und die möglichen sicherheits- relevanten Funktionen zu bestimmen. Es ist die Verantwortung des Kunden, in sicherheitsrelevanten Anwendungen geeignete Maßnahmen zur Erreichung der Sicherheit zu ergreifen (Sensorredundanz, Plausibilitätsprüfung,...

Open the catalog to page 11

All RHEINTACHO Messtechnik GmbH catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list