Exhibit with us
*mydirectindustry  
English
  1. Catalogs
  2. REXEL
  3. SELF SERVE CAR WASH DRYER FUKA - INSTALLATION

SELF SERVE CAR WASH DRYER FUKA - INSTALLATION

SELF SERVE CAR WASH DRYER FUKA - INSTALLATION
1 / 6 PagesView full catalog

SELF SERVE CAR WASH DRYER FUKA - INSTALLATION

Product catalog summary
Installation Preparation
The machine must be assembled on a pre-constructed concrete foundation using the provided steel anchors. A trench with dimensions of 40cm x 20cm and a depth of 90cm should be dug. The anchors must be placed in the trench, ensuring the top plate connecting all four anchors is level and flush with the ground, representing the top level of the foundation.

Power Cable Installation
Between the anchors, lay the power cable in a corrugated plastic sleeve, leaving at least 200cm of excess cable above ground. Stabilize the setup and pour concrete of at least class B20. Foundation work should be conducted at temperatures above 5 degrees Celsius.

Stage I: Foundation Construction
1. Dig the trench and place the anchors.
2. Lay the power cable and stabilize the setup.
3. Pour concrete of at least class B20.

Stage II: Above-ground Assembly
Assembly of the connector element on the concreted parts should occur no sooner than 7 days after foundation construction. The distance from the bottom of the connector element to the foundation level should be approximately 25mm.

Assembly Instructions
1. At the installation site, dig a hole with dimensions of 40x200mm and a depth of 900mm.
2. After stabilizing the anchors, insert a conduit for the power cable and fill with concrete of at least class B20.
See more

Catalog excerpts

SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-1

INSTALLATION PREPARATION

 Open the catalog to page 1
SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-2

STAGE I Foundation Construction The machine must be assembled on a previously made concrete foundation using the steel anchors provided in the set. A trench should be dug with dimensions 40cm x 20cm and a depth of 90cm. Place the anchors in the trench, ensuring that the top plate connecting all 4 anchors is level. The plate should be flush with the ground level and represent the top level of the foundation. Between the anchors, lay the power cable in a corrugated plastic cable sleeve. Leave an excess of cable above ground level, with a minimum length of 200cm. Stabilize the entire setup and pour...

 Open the catalog to page 2
SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-3

Foundation anchors with power cable cable shield power cable ground level power cable

 Open the catalog to page 3
SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-4

STAGE II Above-ground assembly of the machine no sooner than 7 days after foundation construction Assembly of the connector element on the concreted parts. The distance from the bottom of the connector element to the foundation level should be approximately 25mm. Assembly of the connector element

 Open the catalog to page 4
SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-5

Anchors for embedding in the ground At the installation site, dig a hole with dimensions of 40x200mm and a depth of 900mm. After stabilizing the anchors, insert a conduit for the power cable and fill with concrete of at least class B20

 Open the catalog to page 5
SELF SERVE CAR WASH DRYER FUKA - INSTALLATION-6

Poziom terenu

 Open the catalog to page 6

All REXEL catalogs and technical brochures

  1. ULTRASONIC MANUAL CUTTER FOR TEXTILES TTS-400
    ULTRASONIC MANUAL CUTTER FOR TEXTILES TTS-400

    1  Page

  2. MANUAL FABRIC END-CUTTER, MANUAL ELECTRIC CUTTER TEXTILE OT-1/R - OT-2/R
    MANUAL FABRIC END-CUTTER, MANUAL ELECTRIC CUTTER TEXTILE OT-1/R - OT-2/R

    1  Page

  3. SEMI-AUTOMATIC FABRIC END-CUTTER, TEXTILE CUTTER OT-1/A - OT-2/A
    SEMI-AUTOMATIC FABRIC END-CUTTER, TEXTILE CUTTER OT-1/A - OT-2/A

    1  Page

  4. MANUAL FABRIC SPREADING MACHINE, MANUAL SPREADER UL-3
    MANUAL FABRIC SPREADING MACHINE, MANUAL SPREADER UL-3

    2  Pages

  5. CUTTING ROOM TABLE WITH AIR BLOWING, AIR CUSHION SK-3 AIR
    CUTTING ROOM TABLE WITH AIR BLOWING, AIR CUSHION SK-3 AIR

    2  Pages

  6. SWIVEL, ROUND CUTTING ROOM WORK TABLE SK-3/O
    SWIVEL, ROUND CUTTING ROOM WORK TABLE SK-3/O

    1  Page

  7. CUTTING ROOM TABLE, TEXTILE CUTTING TABLE, WORKSHOP TABLE SK-3
    CUTTING ROOM TABLE, TEXTILE CUTTING TABLE, WORKSHOP TABLE SK-3

    1  Page

  8. FABRIC, TEXTILE CUTTING MACHINE NTH-100
    FABRIC, TEXTILE CUTTING MACHINE NTH-100

    2  Pages

  9. MATTRESS COVER SEWING TABLE WITH AIR CUSHION SK-3 AIRSEW
    MATTRESS COVER SEWING TABLE WITH AIR CUSHION SK-3 AIRSEW

    2  Pages

  10. PNEUMATIC GANTRY PRESS FOR UPHOLSTERY PDM-3B
    PNEUMATIC GANTRY PRESS FOR UPHOLSTERY PDM-3B

    2  Pages

  11. PNEUMATIC PRESS FOR UPHOLSTERY PDM-1/HD
    PNEUMATIC PRESS FOR UPHOLSTERY PDM-1/HD

    1  Page

  12. PNEUMATIC PRESS FOR UPHOLSTERY PDM-1 MINI (FOR BENCHES, HEADBOARDS)
    PNEUMATIC PRESS FOR UPHOLSTERY PDM-1 MINI (FOR BENCHES, HEADBOARDS)

    1  Page

  13. PNEUMATIC PRESS WITH DRAWSTRING SYSTEM PDK-2/PDS (CORD PULLING)
    PNEUMATIC PRESS WITH DRAWSTRING SYSTEM PDK-2/PDS (CORD PULLING)

    1  Page

  14. PNEUMATIC PRESS FOR UPHOLSTERED SEATS PDK-1
    PNEUMATIC PRESS FOR UPHOLSTERED SEATS PDK-1

    2  Pages

  15. PNEUMATIC PRESS FOR CHAIR UPHOLSTERY PDP-1
    PNEUMATIC PRESS FOR CHAIR UPHOLSTERY PDP-1

    1  Page

  16. PNEUMATIC PRESS FOR UPHOLSTERY PDM-1M-D
    PNEUMATIC PRESS FOR UPHOLSTERY PDM-1M-D

    1  Page

  17. FABRIC REWINDING, INSPECTION AND CUT-TO-LENGTH MACHINE CTLR-2000-K3-0028
    FABRIC REWINDING, INSPECTION AND CUT-TO-LENGTH MACHINE CTLR-2000-K3-0028

    1  Page

  18. CRADLE WITH COUNTER KZL-1 FOR NT-1/L
    CRADLE WITH COUNTER KZL-1 FOR NT-1/L

    1  Page

  19. FABRIC WINDING MACHINE NT-1/L
    FABRIC WINDING MACHINE NT-1/L

    1  Page

  20. FABRIC REWINDING-INSPECTION MACHINE PP-3S
    FABRIC REWINDING-INSPECTION MACHINE PP-3S

    2  Pages

  21. FABRIC REWINDING MACHINE P-3S
    FABRIC REWINDING MACHINE P-3S

    2  Pages

  22. FABRIC REWINDING MACHINE P-4SE
    FABRIC REWINDING MACHINE P-4SE

    2  Pages

  23. BAND KNIFE MACHINE R500/F
    BAND KNIFE MACHINE R500/F

    2  Pages

  24. BAND KNIFE MACHINE R750
    BAND KNIFE MACHINE R750

    2  Pages

  25. BAND KNIFE MACHINE WITH SLIDING TABLE R1000/PB
    BAND KNIFE MACHINE WITH SLIDING TABLE R1000/PB

    2  Pages

  26. BAND KNIFE MACHINE / BAND SAW R1000
    BAND KNIFE MACHINE / BAND SAW R1000

    2  Pages

  27. BAND KNIFE MACHINE FOR UPHOLSTERY FOAM R1150
    BAND KNIFE MACHINE FOR UPHOLSTERY FOAM R1150

    2  Pages

  28. BAND KNIFE MACHINE R1250
    BAND KNIFE MACHINE R1250

    2  Pages

  29. BAND KNIFE MACHINE WITH SLIDING TABLE R1150/PB
    BAND KNIFE MACHINE WITH SLIDING TABLE R1150/PB

    2  Pages

  30. PNEUMATIC LIFTING TABLE FOR SOFA PACKAGING ST-6
    PNEUMATIC LIFTING TABLE FOR SOFA PACKAGING ST-6

    2  Pages

  31. FOIL UNWINDING AND CUTTING TABLE K2-0597
    FOIL UNWINDING AND CUTTING TABLE K2-0597

    1  Page

  32. TILT ABLE PACKAGING AND ASSEMBLY TABLE SOP-1
    TILT ABLE PACKAGING AND ASSEMBLY TABLE SOP-1

    1  Page

  33. PNEUMATIC LIFTING TABLE FOR GLUING ST-4/B
    PNEUMATIC LIFTING TABLE FOR GLUING ST-4/B

    1  Page

  34. PNEUMATIC LIFTING TABLE FOR SOFA PACKAGING ST-3 OC
    PNEUMATIC LIFTING TABLE FOR SOFA PACKAGING ST-3 OC

    2  Pages

  35. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3 ROL MINI
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3 ROL MINI

    1  Page

  36. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KRB C
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KRB C

    2  Pages

  37. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 HD KRB
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 HD KRB

    1  Page

  38. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KPO
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KPO

    2  Pages

  39. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KRB B
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-7 KRB B

    1  Page

  40. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3

    1  Page

  41. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/B
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/B

    1  Page

  42. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/BR
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/BR

    1  Page

  43. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/KP
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/KP

    1  Page

  44. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/K
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/K

    1  Page

  45. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/R
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/R

    1  Page

  46. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/RB
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/RB

    1  Page

  47. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/KRB
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/KRB

    1  Page

  48. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/HD
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/HD

    1  Page

  49. AUTOMATED PHARMACY DISPENSING SYSTEM FABLOX 2.0 SLIM
    AUTOMATED PHARMACY DISPENSING SYSTEM FABLOX 2.0 SLIM

    2  Pages

  50. REXEL 2023: Industrial sewing machine stands
    REXEL 2023: Industrial sewing machine stands

    24  Pages

  51. REXEL 2022: Equipment for the production of roller blinds
    REXEL 2022: Equipment for the production of roller blinds

    18  Pages

  52. REXEL 2026: Main catalogue
    REXEL 2026: Main catalogue

    34  Pages

  53. SELF SERVE CAR WASH DRYER FUKA
    SELF SERVE CAR WASH DRYER FUKA

    8  Pages

  54. FUKA - PREPARATION FOR INSTALLATION CONCRETE FOUNDATION
    FUKA - PREPARATION FOR INSTALLATION CONCRETE FOUNDATION

    5  Pages

  55. FUKA - PREPARATION FOR INSTALLATION CHEMICAL ANCHOR
    FUKA - PREPARATION FOR INSTALLATION CHEMICAL ANCHOR

    5  Pages

  56. MATERIAL ROLL RACK LS-8
    MATERIAL ROLL RACK LS-8

    1  Page

  57. FABRIC CUTTING MACHINE NTH-125
    FABRIC CUTTING MACHINE NTH-125

    2  Pages

  58. MANUAL MEASURING STOPS PR-11
    MANUAL MEASURING STOPS PR-11

    2  Pages

  59. FABRIC REWINDING-INSPECTION MACHINE PP-3S
    FABRIC REWINDING-INSPECTION MACHINE PP-3S

    2  Pages

  60. FABRIC REWINDING MACHINE P-3L
    FABRIC REWINDING MACHINE P-3L

    2  Pages

  61. TILT ABLE PACKAGING AND ASSEMBLY TABLE
    TILT ABLE PACKAGING AND ASSEMBLY TABLE

    2  Pages

  62. MANUAL FABRIC END CUTTER FOR THICK MATERIALS OT-1/RH
    MANUAL FABRIC END CUTTER FOR THICK MATERIALS OT-1/RH

    1  Page

  63. ROLLER TABLE SK-3/ROL
    ROLLER TABLE SK-3/ROL

    1  Page

  64. INDUSTRIAL FEED OFF THE ARM STAND REX-5S
    INDUSTRIAL FEED OFF THE ARM STAND REX-5S

    1  Page

  65. INDUSTRIAL FEED OFF THE ARM STAND REX-5K
    INDUSTRIAL FEED OFF THE ARM STAND REX-5K

    1  Page

  66. PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/WR
    PNEUMATIC LIFTING TABLE FOR UPHOLSTERY ST-3/WR

    1  Page

  67. Pneumatic scissor lifting tables for upholstery REXEL
    Pneumatic scissor lifting tables for upholstery REXEL

    7  Pages

  68. Industrial chairs REXEL for sewing factories
    Industrial chairs REXEL for sewing factories

    2  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.