*mydirectindustry

Catalogs
Renu Electronics GmbH
FP6CN-M Rugged HMI Series

FP6CN-M Rugged HMI Series

1 / 2 PagesView full catalog

FP6CN-M Rugged HMI Series

Product catalog summary

Product Specifications

Models: FP6070CN-M (7” TFT) and FP6101CN-M (10.1” TFT)
Power: 24VDC(±15%), 7.0” at 800mA (19.2W), 10.1” at 780mA (18.72W)
Display: 1024 x 600 pixels, capacitive touch screen, brightness 1000 Nits
CPU: Cortex A53 Quad core 1.4GHz, Cortex M4 400MHz
Memory: eMMC 16GB, RAM 2GB
Dimensions: FP6070CN-M: 146.20(H) x 213.50(W) x 46.80(D) mm, FP6101CN-M: 199.30(H) x 280.70(W) x 46.70(D) mm
Communication: 2 x RS232/RS485, 1 x USB Type-C, 2 x USB 2.0, 2 x Ethernet (10/100MBps), 1 x CANopen Channel
Environment: Operating Temperature -20°C to 70°C, Humidity 10 to 90% (Noncondensing), IP66 protection
Approvals: RoHS compliant

Installation and Configuration Procedure

Install FlexiSoft Software.
Create an FP application using FlexiSoft software.
Connect programming cable.
Download Firmware for the HMI.
Download application.
The FP unit is now ready for use.

Communication Interfaces

COM Ports: RS485/RS232 with specific pin configurations.
USB Host Port: Compliant with USB 2.0, supports USB memory stick devices, current up to 150mA.
Ethernet Port: Compliant with IEEE 802.3 / 802.3u standards, supports 10/100 Mbps.

Earthing Recommendations

Electronic equipment should be earthed separately from high-power systems. Use a single-point earth for multiple units. Avoid unstable impedance connections.

Additional Notes

Renu Electronics Pvt. Ltd reserves the right to change specifications without notice. For updated datasheets/manuals, visit www.renuelectronics.com.

Catalog excerpts

Product Code FP6070CN-M: 7” TFT, 24VDC, 2 Serial ports (RS232 / RS485), 1 CANopen, 1 USB Type C, 2 USB Host, 2 Ethernet, 1 Micro SDHC. FP6101CN-M: 10.1” TFT, 24VDC, 2 Serial ports (RS232 / RS485), 1 CANopen, 1 USB Type C, 2 USB Host, 2 Ethernet, 1 Micro SdHC. User should follow the given sequence to configure and use any FlexiPanels series unit: 1. Install FlexiSoft Software. 2. Create a FP application using FlexiSoft software. 3. Connect programming cable. 4. Download Firmware i.e. driver for the HMI. 6. Now FP unit is ready to use in the system. Krenu For More Information, Visit http s://www.re nue lectron ics.com Panel Dimensions Panel Cutout Dimensions Power (Base)

Open the catalog to page 1

FP6101CN-M Panel Cutout Dimensions: 187.90 (H) x 269.30(W) mm The FP6-M PCAP series comes with a Type C USB port. Revision History built speed and link activity indication LEDs. 1. USB Host, compliant with USB 2.0 specification 2. USB Host can be used to transfer logged data and historical alarm to USB memory stick. 3. USB Host can handle only USB memory stick devices and can source current up to 150mA only. 4. Connector used: Standard USB Type a Female Earthing The optimum method for earthing electronic equipment is to earth it separately from other high-power systems, to earth more than one...

Open the catalog to page 2

All Renu Electronics GmbH catalogs and technical brochures

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.

Brand list