Catalogs >
Renu Electronics GmbH >
FlexiLogics®- Standard PLC Series

FlexiLogics®- Standard PLC Series
1 / 7Pages

Catalog excerpts

FlexiLogics®- Standard PLC Series SALIENT FEATURES  DIN rail / Back panel mounted PLC  Transistor (NPN) or Relay Outputs  32 Bit RISC Processor  DC Inputs and DC Outputs  Built-in RTC  Up-to 2 Serial Ports (1x RS232) and (1x RS485)  Strong communication capabilities where PLC can be configured as Modbus RTU Master or Slave  Expandable up to 16 expansions  DC powered units (24VDC)  IEC61131-3 Programming environment support  CE approved

Open the catalog to page 1

MODEL COMPARISON Part Number Power Supply (+20%, -15%) Program Memory (Application + Ladder) Program Capacity Input Signal Total Channels Isolation High Speed Inputs Single Phase Inputs Quadrature Inputs Total Channels Output Type Nominal Load Current per channel High Speed Outputs 4 Channels (Up-to 200kHz each) Communication Serial USB Device Ethernet Operating Temperature Storage Temperature Humidity Shock Vibration Approvals 10 to 90% (Noncondensing) IEC 60068-2-27, 25g, 11ms, 6 shocks per axis, total 18 shocks (X, Y, Z) 5~150Hz, 3g peak, (X, Y, Z) CE & RoH

Open the catalog to page 2

APPLICATION EXAMPLE DIGITAL EXPANSION MODULES Model 8 Digital Outputs (Relay) 8 Digital Inputs, 8 NPN type Outputs 8 Digital Inputs, 8 Relay type Outputs 16 Digital Outputs (Relay) ANALOG EXPANSION MODULES Model 4 Universal Inputs (0-5V / 0-10V / 0-100mV / 0-50mV / 020mA / 4-20mA / RTD PT-100, PT-1000 / Thermocouple - B, R, S, E, J, K, N, T) 2 Analog Outputs (0-10V / 4-20mA/ 0-20mA), 12 Bit LOAD CELL EXPANSION MODULE Model 2 Load cell inputs, 2 NPN transistor outputs Note: Expansion models are subject to change. Please contact factory to check the latest models and their availability.

Open the catalog to page 4

WIRING DIAGRAM Digital Inputs HSC Inputs: Single Phase counter Digital Outputs: (R-Type) Digital Outputs: (N-Type) HIGH SPEED INPUT / OUTPUT CHANNEL DEPENDENCY Pulse Input Pulse Output Either use X0 Pulse Input or Y2 Pulse Output Either use X4 Pulse Input or Y0 Pulse Output Either use X2 Pulse Input or Y4 Pulse Output Either use X6 Pulse Input or Y6 Pulse Output 1. In Single phase/Quadrature, if all the pulse inputs are used at low frequency then the all pulse outputs can be used at 200kHz. 2. In Single phase mode, if all the inputs are used at high frequency then the pulse outputs can not...

Open the catalog to page 5

SOFTWARE OVERVIEW Configuration Software FlexiSoft® is a compact, Windows® based software to configure the PLC. This image from FlexiSoft® shows the snap shot of Programming window. ORDERING INFORMATION Model 8 Bi-directional digital inputs(4 single phase HSC up-to 200kHz or 8 single phase HSC up-to 25kHz) or (2 Quadrature up-to 200kHz or 4 Quadrature up-to 10kHz), 8 NPN-transistor type digital outputs, 4 high speed PWM outputs up-to 200kHz, 16K Steps Memory. Up-to 2 Serial Ports (1x RJ45 RS232 , 1x 3.81 pitch PBT RS485 (2-Wire)), 1 USB Device Port. 8 Bi-directional digital inputs(4 single...

Open the catalog to page 6

SUPPORTED PROTOCOLS ABB PLC Allen Bradley DF1 Baldor Danfoss Drive Delta PLCs Fatek PLCs FlexiLogics Slave Driver FlexiLogics Master Driver Serial Printer Siemens Step-7 Micro Idec PLCs LG Master K Series PLC LG Master K 300S Mitsubishi FX GE SNP Mitsubishi Q Series PLCs (Serial) Modbus ASCII (Unit as Master) Modbus RTU (Unit as Master) Modbus RTU (Unit as Slave) Omron Inverter Memobus Omron Host Link Panasonic FP Series Siemens Micromaster Driver (USS) Toshiba (Link Port) Series PLCs Toshiba Inverters PLCs Toshiba T Series TriPLC Universal Serial Driver(ASCII) Unitelway PLCs GE SNP-X...

Open the catalog to page 7