Robotics
12Pages

ROBOTIC CABLE MANAGEMENT SOLUTIONS REIKU's Patented Robotic Cable Saver™ complete modular solution REIKU NORTH AMERICA www.reikuna.com

Compatible with all makes and models of Robots Almost 85% of Robotics and Automation “downtime” can be directly attributed to cable or hose failure. STOP Cable failures and Robotic downtime Cable Saver™ Our Cable Saver™ Solution eliminates : Downtime loss of revenue, Expensive cable & hose replacement costs, Maintenance labour costs All of the Robot's cables and hoses are protected when routed through the Cable Saver™ 15 million + cycle corrugated tubing. Robot movements require that there be surplus cables and hoses in order to service these dynamics. The Cable Saver™ uses a spring...

Cable Saver™ Installation Options Each Cable Saver™ Kit comes complete with • Axis 3 REIKU Gripping Clamp Assembly • Patented Energy/Spring Tube complete • Axis 6 REIKU Gripping Clamp Assembly CSK-36 36MM I.D. Cable Saver Kit CSK-52 52MM I.D. Cable Saver Kit CSK-70 70MM I.D. Cable Saver Kit CSMOUNT-STD Cable Saver™ mounting hardware kit- for all sizes A custom prepared grommet known as a Cablestar is a CRUCIAL component that must be installed at both termination points. Cable Saver™ Part numbers • 5 meters/16 feet of REIKU Nylon 12 conduit Precision holes are water-jetted into the soft...

Installed Cable Saver™ Examples

REIKU Component Solution Examples

REIKU Component Solutions Rotary Base Conduit Protector Gripping Clamp Steel Latch Trumpet Ball Connection Joint Ball Joint Cable Star in Clamp Gripping Clamp Nylon Latch Ball Joint Spring Assembly Rotary Fork Assembly

Use our conduit size calculator tool available at All conduits are not created equal ,'. „ REIKU’s patented conduit profile allows for a tighter bending radius without reducing the conduit’s inside diameter. REIKU recommends a maximum 75% conduit fill capacity in order to prevent the chaffing of cables and hoses. Please refer to our conduit size calculator tool at www.reikuna.com. REIKU conduit part numbers contain the actual Inside Diameter or I.D. of the conduit in millimeters The proper conduit diameter selection should be based on the area that is required to fit all of the cables and...

Clamping Optionsto secure the conduit and Abrasion Protection offerings All jaws listed below rotate radially 360° inside gripping clamps. Middle jaws have a ridge to prevent lateral movement of conduit. Sliding jaws have no ridge and allow lateral movement of conduit. with nylon fastener with nylon fastener with nylon fastener with screw fastener with metal fastener with nylon fastener with metal fastener with nylon fastener with screw fastener with nylon fastener with metal fastener REIKU Gripping Clamps must be purchased with one of the 3 available “Jaw-sets” listed. Gripping Clamps are...

Spring Retractor Components In order not to restrict the demanding movements of Robotic applications surplus lengths of cables and hoses are required. These surplus lengths of cables and hoses or service loops as they are known will now be housed inside the REIKU conduit. It is strongly recommended that a spring retraction system be utilized in order to keep this service loop from getting tangled or hung up. Generally the area behind Axis 3 at the rear of the Robot is a "safe area" and the spring system can be installed to pull the conduit back when not required. The spring system can be...

Components for Added Mobility The Rotary Fork has a central pivot point which allows it’s jaw assembly to move up and down in a pitch and yaw motion. Part No. Pkg Qty Used with either PA TBB-70 or PA DMB-70 PATBB-70 Trumpet Jaw for Rotaiy Fork 10 has no ridges to hold conduit and allows lateral movement PA DMB-70 Middle Jaw for Rotary Fork 10 has ridges to prevent conduit moving laterally The Rotary Flange can be installed under most REIKU components and will enable the assembly to rotate on it's base axis acting like a "Lazy Susan" Part No. Pkg Qty PA DFB-42 used with 42 mm REIKU...

Termination Options The use of REIKU Cablestars is crucial in creating an optimal cable management system Trumpet Ball Cablestar grommets CABLESTARS are soft rubber “grommets” that are used at the termination areas of the conduit runs. These Cablestars are custom prepared for the customer’s application. Each hole I.D. is precision water-jet bored to be MINUS 0.50 mm from the O.D of each individual cable and hose . This ensures that the cables and hoses are secured from moving laterally and reduces the strain from connection points. The Cablestars also seal the conduit to prevent foreign...

TURN THIS INTO THIS WITH REIKU CABLE SAVER™ ADDITIONAL REIKU HI-TECH CABLE PROTECTION PRODUCT LINES REIKU GL HEAT PROTECTION HIGH TEMPERATURE MATERIALS REIKU ELECTRICAL CONDUIT AND CONNECTOR SYSTEMS REIKU ZIPPERED CABLEBUNDLING SYSTEMS REIKU EMI AND FINE BRAIDED MATERIALS For information or product catalog on REIKU® in North America contact: 1500 Commerce Drive Stow, OHIO 44224 Toll Free: 1-800-841-5804 Fax: 330-688-8460 Email: info@reikuna.com www.reikuna.com P.O. Box 2000, 157 North Murray Street Trenton, Ontario K8V 6G7 Tel: 613-394-4817 • Fax: 613-394-5516 Exclusive Partner of REIKU ®...