High-speed extruder
High-speed extruder
The document provides detailed information about high-speed extruders designed for processing materials such as PS, PP, and LD-PE. These extruders are noted for their compact design and high plasticizing capacity, achieved through increased screw speeds, while maintaining a reduced footprint.
Specifications
- Barrel Wear Protection: Options include high-alloyed hard phasing alloy on iron base, with vanadium carbides, or two-phase hard alloy on nickel base with tungsten carbides.
- Screw Wear Protection: Ranges from high surface hardness to maximum protection against abrasion, corrosion, and adhesion.
- Base Frame: Available in stationary, movable, or customized designs.
- Drive: Features an asynchronous drive with a water-cooled motor.
- Gear Box: Designed by Reifenhäuser for longevity and backward screw removal.
- Barrel Design: Options include closed, with vacuum venting opening and closure plug, or with vacuum dome.
- Connection Flange: Standard or customized hole patterns, with wedge closing device.
- Feed Opening: Equipped with cooling and material outlet.
- Water Installation: Direct connection or centralized distribution with optional chiller.
- Heating Units: Include convection flaps, heat isolation, and protection against contact.
- Cover Hood: Options for barrel hood or full cover.
- Suction Hood: Standard or integrated in full cover hood.
- Electrification: Direct connection, terminal box, or electrical cabinet with control unit.
Extruder Configuration
The extruders can be configured in three equipment variants: Smart, Advanced, and Premium, allowing customization to specific requirements.
Performance Data
The document lists five high-speed extruder models (HS 1 to HS 5) with varying drive power, screw speed, and plasticizing capacities for PP, PS, and LDPE. Capacities range from 100 to 1250 kg/h depending on the model and material.
Contact Information
Reifenhäuser Extrusion Systems GmbH, located in Troisdorf, Germany, provides contact details for further inquiries.
Catalog excerpts
EXTRUSION SYSTEMS High-speed extruder Our high-speed extruders for processing PS, PP, and LD-PE are extremely compact. The high screw speeds achieve much higher plasticizing capacity compared to conventional extruders. At the same time, they have a significantly reduced footprint.
Open the catalog to page 1
High-speed extrudersPortfolio Extruder RH034-1-70-36D Plasticizing Srew speed capacity PP Plasticizing Plasticizing capacity PS capacity LDPE You can configure your high-speed extruder to your requirements using our three equipment variants. High-speed extruder setup Assembly Group Barrel [Wear Protection] High-alloyed hard phasing alloy on iron base High-alloyed hard phasing alloy on iron base with vanadium carbides Two-phase hard alloy on nickel base s with tungsten carbides Screw [Wear Protection] Screw with high surface hardness Armored screw flight with high wear protection against abrasion...
Open the catalog to page 2All Reicofil catalogs and technical brochures
Flat die Extrusion coating2 Pages
Refeeding extruders2 Pages
ReiMix-HS mixing element2 Pages
Extruder2 Pages
ULTRA STRETCH All-PE Films2 Pages
Coextrusion Systems4 Pages
Reifenhäuser Group8 Pages
Cast-Sheet- and Coating Lines52 Pages
EVO Blown Film Lines40 Pages
- Reifenhäuser extrusion line
- Reifenhäuser thermoplastic extrusion line
- Panel extrusion line
- PP extrusion line
- PE extrusion line
- Flat-film extrusion line
- Reifenhäuser blown film extrusion line
- Twin-screw extrusion line
- PET extrusion line
- PS extrusion line
- PLA extrusion line
- Coating extrusion line
- PA extrusion line
- Filament extrusion line
- Stretch film extrusion line
- Agricultural film extrusion line
- Barrier film extrusion line
- CPP extrusion line
- Research and development extrusion line