REFOND P/N 产品型号 RF-FT4F***68-T3-B/-P
19Pages

产品规格书 REFOND P/N 产品型号 RF-P**MI32DS-BF-N-Y REFOND P/N 产品型号 RF-FT4F***68-T3-B/-P □R&D 研发 ■Mass Product 量产供货

1. Description 产品介绍 1.1 General Description 产品描述 The White LED, which was fabricated by using a blue chip and the phosphor. Product Package:40.0mm×1.5mm×2.2mm. 该产品为白光 LED，是由蓝光芯片激发荧光粉而形成，产品尺寸：40.0mm×1.5mm×2.2mm。 1.2 Features 产品特征 ► IntegratedPackage.集成封装 ► 360 ° Full Angle Luminescence.360°全角度发光 ► Suitable for spot welding process . 适用于点焊工艺 ► Moisture sensitivity level: Level 5.防潮等级 Level 5 ► RoHS compliant.满足RoHS要求 1.3 Application 产品应用 ► Indoor lighting.室内照明 ► Decorative

1.4 Package Dimension 封装尺寸 1.5 Fig.1-2 Side View 侧面视图 Fig.1-3 Whole Line View 整排视图 Notes 备注： 1. All dimensions units are millimeters. 所有尺寸标注单位为毫米 2. All dimensions tolerances are 0.5mm unless otherwise noted.除特别标注外，所有尺寸公差为±0.5 毫米

1.5 Product Parameters 产品参数 Table 1-1 Electrical / Optical Characteristics at Ts=25° 电性与光学特性 C Value Test Condition 测试条件 Forward Voltage （正向电压） Viewing Angle （发光角度） Solder Temperature （焊点温度） Table 1-2 Absolute Maximum Ratings at Ts=25° 绝对最大值 C Parameter（参数） Forward Current （正向电流） Peak Forward Current （峰值电流） Electrostatic Discharge (HBM)（静电） Operating Temperature （操作温度）

TG-201806120994NP Notes 备注： 1. 1/10 Duty cycle, 0.1ms pulse width. 脉宽0.1ms,占空比1/10. 2. The above forward voltage measurement allowance tolerance is ±1V. 以上所示电压测量误差 ±1V. 3. The above color coordinates measurement allowance tolerance is ±0.005. 以上所示坐标测量误差± 0.005. 4. The above luminous intensity measurement allowance tolerance ±10%. 上述发光强度的测试允许公差为±10%. 5. Care is to be taken that power dissipation does not exceed the absolute maximum rating of the product. 使用 功率不能超过规定的最大值。 6. All measurements were made under the standardized environment of Refond. 所有测试都是基于瑞丰现有的 标准测试平台。 7.When the LEDs are in...

PAGE:7 js . i ^ / Innovation enrich life

1.7 Typical Optical Characteristics Curves 典型光学特性曲线 30 Fig. 1-7 Forward Voltage Vs Forward Current伏安特性曲线 Relative Intensit（%） Fig. 1-8 Forward Current Vs Relative Intensity正向电流与相对光强特性曲线

Relative Intensity(%) Fig. 1-9 Solder Temperature Vs Relative Intensity焊点温度与相对光强特性曲线 Fig. 1-10 Forward Voltage Vs Solder Temperature电压与焊点温度特性曲线

Relative Luminous Intensity Relative Emission Intensity (%)

2. Packaging 产品包装 2.1 Packaging Specification 包装规格 Single :1200pcs/box 单根包装每包 1200pcs Whole Row: 4320pcs/box 整排包装每包 4320pcs 2.1.1 Suction box Dimension 吸塑盒尺寸 Fig.2-1 Suction box Dimension 吸塑盒尺寸 Notes 备注： The tolerances unless mentioned ±0.1mm. Unit : mm 注：未注公差为±0.1毫米，尺寸单位：毫米。

2.1.2 Label Form Specification 标签规格 Table 2-1 Title 表名 产品名称 Bom 号 Forward Voltage 正向电压 Made Date 生产日期 2.2 Moisture Resistant Packing 防潮包装

深圳市瑞丰光电子股份有限公司 SHENZHEN REFOND OPTOELECTRONICS CO.LTO. 2.4 Reliability Test Items And Conditions 信赖性测试项目及条件 Table 2-2 Reliability Test Items And Conditions 信赖性测试项目及条件 Test Items Test Condition -40℃ 15min Thermal Shock 冷热冲击 Switching Test 开关测试 Life Test 常温通电 High Temperature High Humidity Life Test 高温高湿通电

2.5 Criteria For Judging Damage 失效判定标准 Table 2-3 Criteria For Judging Damage 失效判定标准 Test Items Test Condition Forward Voltage 正向电压 正向电压 Luminous Flux Notes 备注： 1.U.S.L: Upper standard level 规格上限 L.S.L: Lower standard level 2. The above reliability tests is based on the verification of a single/strip LED of Refond's existing experimental platform, the reliability experiment was taken under good heat dissipation conditions. when customers applies the LED to the series and parallel circuit, should take consideration of all the factors such as the current, voltage distribution, heat dissipation...

3. Handling Precautions 产品使用注意事项 (1) LED operating environment and sulfur element composition cannot be over 100PPM in the LEDmating usage material. This is provided for informational purposes only and is not a warranty or endorsement.LED 工作环境及与 LED 适配的材料中硫元素及化合物成份不可超过 100PPM.这只 是一个建议，不作任何品质担保。 (2) In order to prevent ex-ternal material from getting into the inside of LED, which may cause the malfunction of LED, the single content of Bromine element is required to be less than 900PPM,the single content of Chlorine elementis required to be less than 900PPM, the total content of Bromine...

(4) Handle the component along the side surface by using forceps or appropriate tools; Do not directlytouch or Handle the silicone lens surface, it may damage the internal circuitry.通过使用适当 的工具从材料侧面夹取，不可直接用手或尖锐金属压胶体表面，它可能会损坏内部电路。 (5) In designing a circuit, the current through each LED can not exceed the absolute maximum rating specified for each LED. In the meanwhile,resistors for protection should be applied, otherwise slight voltage shift will cause big current change,burn out may happen. The driving circuit must be designed to allow forward voltage only when it is ON or OFF.If the...

要求较高时，回流焊以后需要采用恰当的清洗方式，我们推荐用异丙醇作清洗剂，如需要用到其他 清洗剂，必须保证不会破坏封装体，超声清洗可能会对 LED 带来损害，不推荐这种清洗方式。 Table 4-1Storage 储存 Conditions Before Opening Aluminum Bag Within 1 Year From Date ≤30℃ After Opening Aluminum Bag (8) If the moisture absorbent material（silica gel）has faded away or the LEDs have exceeded the storage time, baking treatment should be performed after unpacking and based on the following condition（65±5）℃ for above 24 hours.如果干燥剂或包装失效，或者产品不符合以上 有效储存条件，需拆包后进行烘烤，烘烤条件：60±5℃，大于 24 小时。 If the package is flatulence or damaged, please notify the sales staff to assist.如果包装胀气或者 破损，请通知销售人员协助处

Version History/修订历史 Date日期

Declare 申明 This specification is written both in English and in Chinese and the latter is formal. 产品规格书以中英文方式书写，若有冲突以中文版本为准。 Tel: +86-755-66839118 Fax:+86-755-66839300 REFOND:WI-E-045 A/3 REV:E/1