Power Rider 150A
12Pages

DATASHEET Power Rider 150A Catalog number P/N: RD000112 Power Rider 150A – Protect, Manage and Maintain Smart, Electronic Circuit Breaker and EPD Building Block Functionality: • Circuit breaker (fuse), relay, and contactor in the same product Two levels of protection: ∙ Software – I²t, over-current, over-voltage, over-temperature. ∙ Hardware – 1μ second cutoff of over current Solid-state-based technology Circuit breaker support network Configurable – over 20 flexible configuration parameters Building block for ‘Power Distribution Unit’ Measurement of input voltage, output voltage, load current and temperature Advanced reporting and easy maintenance – event logs, graphs, conditional alerts Discrete I/O: 4 digital input, 4 digital output (open collector) Operation switch with smart indicator light: channel consumption, channel status, fail indicators BIT (Power-on and On-the-fly built-in test) MTBF – 41.6 Years (24 working hours per day) Comply with MIL-STD 810F P/N: RD000112 Redler Technologies Ltd. ● Atir Yeda St. 15 ● Kfar Saba Israel www.redlertechn

Power Rider 150A Configuration: Over Current Parameter controlled by the user Parameter controlled by the user Voltage Error Parameter controlled by the user (low voltage, high voltage) Temperature Error Parameter controlled by the user (low temperature, high temperature) Trip Event (Software) Trip event software protection. Trip Event (Hardware) Trip event hardware protection (hard short). Not controlled by the user. Trip Recovery Channel Logic Control Digital Output Logic Control Channel Control Timeout. Parameter controlled by the user Digital Output control Timeout. Parameter controlled...

User Interface Description Figure 1 User Interface Connection Side Control Connector Communication and digital interface Power Input + (+Vin) Power Output (Load) User Interface Input Terminal Ring IN/OUT screw User Interface IN and OUT screw Power Supply return User Interface GND Terminal Ring Terminals Ring M3 Molex 193240006 User Interface GND screw Mounting Screws Countersunk Head Phil. Screw PRESS-FIT Terminals M6 PRESS-FIT Terminals M6 WE5580616 for 8AWG cable or WE5580635 for 10 AWG cable Use Loctite 242 to secure the connection Table 2 User Interface Table P/N: RD000112 Redler...

Control Connector Signal Description: Signal Type Signal Name - Signal Description Signal Ground (Isolated GND) Open drain 0.25 Ampere output. See Digital Output table below. GP* Digital Input, see Digital Input table below. GP* Digital Input, see Digital Input table below. Unit Address 2 Leave open to “0” logic, connect to pin1 to “1” Communication CANBUS channel (CAN Low) Host ON/OFF Apply 12-33V to Shut Down state. See Shut Down table below. GP* Digital Input, see Digital Input table below. Unit Address 0 Leave open to “0” logic, connect to pin1 to “1” Not available in this product....

Electrical Interface: Power Supply Parameter Power Input Voltage (Recommended Ratings) Power Input Voltage (Absolute Maximum Ratings) Power consumption (operating) @28V Power consumption (power down mode) @28V Total channel Current Control Voltage via J1 (Recommended Ratings) Control Current via J1 Typical General Purpose Interface Parameter Digital Output Voltage Digital Output Current Digital Power Output (D.out-4) Digital Power Output (D.out-4) Current Digital Input Voltage Digital Input Current Remarks open collector open collector open collector open collector active low Unit Kbit/sec...

Circuit Breaker Connections: Power Connection The Power Rider 150A circuit breaker is connected in series with the positive power line between the power source and the load. This means that the power flows from the power source, through the Power Rider circuit breaker, and to the load. The circuit breaker acts as a protective device, monitoring the current and interrupting the power flow if an overcurrent or fault condition is detected. Ground Connection The ground connection in the system serves two purposes: 1. Load Grounding: The ground is connected directly from the power source to the...

Physical Connections for Digital Input: Name J1/pin# Active Low Active High DIN 1/ Host ON_OFF V DIN 1/ Host ON_OFF 7 Host ON_OFF V DIN 2 3 V V DIN 3 8 V DIN 4 4 Gray font - not available in this product, for more information please contact support. Active Low Connection P/N: RD000112 Redler Technologies Ltd. ● Atir Yeda St. 15● Kfar Sava ● Israel www.redlertechnologies.com ● Tel: +972 9-7672980

Power Down (Host On/Off) - Active High Connections Din xx – Host ON/OFF (J1/pin 7). GND_ISO1 - Ground (J1/pin1) Physical Connections for Digital Output: J1/pin# Active Low Active High Power Output V V D-out 1 12 D-out 2 15 V V V D-out 3 2 V D-out 4 (Power Output) 13 *Gray Font - Not available in this product, for more information please contact support. Active Low Connection P/N: RD000112 Redler Technologies Ltd. ● Atir Yeda St. 15● Kfar Sava ● Israel www.redlertechnologies.com ● Tel: +972 9-7672980

Active High Connection Protected Output (D-out 4) - J1/13 PWR_GND – Power GND Control Voltage (operation power supply input) Name J1/pin# V Control Voltage 10 PF1 (Power Input) V *Gray Font - Not available in this product, for more information please contact support. P/N: RD000112 Redler Technologies Ltd. ● Atir Yeda St. 15● Kfar Sava ● Israel www.redlertechnologies.com ● Tel: +972 9-7672980

Heat Distribution Description: Power dissipated from Power Rider 150A is Current ²*(RDS+ other serial elements) For single row (RDS+ other serial elements) 7mΩ (typical) For Dual row (RDS+ other serial elements) 12mΩ (typical) Temperature elevation [°C] <5 15 25 Use Heatsink Use Heatsink Use Heatsink Temperature elevation [°C] <10 30 Use Heatsink Use Heatsink Use Heatsink Use Heatsink Dual Row RD000252 *Gray font - not available in this product, for more information please contact support. P/N: RD000112 Redler Technologies Ltd. ● Atir Yeda St. 15● Kfar Sava ● Israel...