RACT18
5Pages

TRIAC Dimmable LED Driver • Triac –dimmable with leading or trailing edge dimmers • Class II with SELV output (no earth required) • Extra-large screw terminals and integrated cable clamps for easy installation • Power factor corrected >0.95 • Dimming range 1..100% • Compatible with a wide range of dimmers AC/DC Converter RACT18 18 Watt 3 TRIAC Dimmable Single Output The RACT18-xxx series are low cost, triac-dimmable, constant current 18W LED drivers available with either 350mA, 500mA, 700mA, 1.05A or 1.4A full-range outputs. The drivers are Class II (double insulated) meaning no earth connection is required. The phase angle dimming works with leading or trailing edge dimmers. The RACT18 is suitable for indoor locations up to 50°C ambient temperature and is certified for building into furniture for applications such as dimmable shelf lighting, cove lighting or accent lighting. It is CE (LVD + EMC + RoHS) + EAC marked and has the international IEC61347-1 CB report certification. Selection Guide Part Number Input Output Output Efficiency Output Voltage Range Voltage Range Current min. @rated load Power [VAC] [VDC] [mA] [%] [W] 198-264 26-52 350 85 18 CONVER All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Model Numbering IEC/EN61347 certified IEC/EN61347-2-13 certified EN61547 certified EN62493 certifed EN55015 compliant CB report Output Current Specifications (measured @ Ta= 25°C, 240VAC, rated load unless otherwise specified) BASIC CHARACTERISTICS Parameter Input Current Inrush Current Input Voltage Range full load No Load Power Consumption Input Frequency Range Power Factor full load full load Start-up Time 500ms continued on next page

Specifications (measured @ ta= 25°C, 240VAC, rated load unless otherwise specified) Parameter Internal Operating Frequency Output Ripple Current (1) Notes: Note1: Measured at 20MHz BW by using a 12” twisted pair-wie terminated with a 0.1µF and 47µF capacitor parallel across output REGULATIONS Parameter Output Accuracy Load Regulation Line Regulation PROTECTION Parameter Input Fuse fusible resistor Short Circuit Protection (SCP) Latch OFF, auto recovery after fault condition is removed 60VDC max. 43VDC max. 33VDC max. 24VDC max. 22VDC max. Over Voltage Protection (OVP) Over Load Protection...

Specifications (measured @ Ta= 25°C, 240VAC, rated load unless otherwise specified) Derating Graph (@ Chamber and natural convection 0.1m/s) Output Load [%] SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report Number Lamp controlgear Part 1: General and safety requirements (CB Scheme) Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (CB Scheme) Lamp controlgear Part 1: General and safety requirements (LVD) Lamp controlgear Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED...

Specifications (measured @ Ta= 25°C, 240VAC, rated load unless otherwise specified) DIMENSION and PHYSICAL CHARACTERISTICS Parameter Package Dimension (LxWxH) Package Weight wire stripping length: 6-7mm recommended tightening torque: 0.25Nm tc= case temperature measuring point FC fixing centers = Tolerance: xx.x= ±1.0mm xx.xx= ±0.5mm Bottom View Connection via Screw Terminal FC 13.3 without cable cover`s Notes: Note2: The use of sleeve or ferrule terminations is recommended

Specifications (measured @ Ta= 25°C, 240VAC, rated load unless otherwise specified) INSTALLATION and APPLICATION Dimming Type work with leading/trailing edge dimmers PACKAGING INFORMATION Parameter Packaging Dimension (LxWxH) Packaging Quantity Storage Temperature Range Storage Humidity The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s...