--[--[■Communication Crystals Acceleration tolerant SMD AT-cut quartz crystal in ceramic package with 6.0 mm x 3.5 mm footprint aSjduct description Very small SMD AT-cut quartz crystal specifically designed to operate in vibration prone environments. Parts are able to survive acceleration 20,000G and higher with minimal parameter change. Vibration G-sensitivity significantly reduced. True SMD style, ceramic package with metal lid, seamed sealed. The product is supplied on tape and reel. Applications • GPS • Agriculture • Avionics • Guidance • Navigation • Military • Other Features • G-sensitivity down to 0.2ppb/G • Low aging • Up to 50,000G acceleration event survival • Very good short term stability Specifications 1.0 SPECIFICATION REFERENCES Line Parameter Description 1.4 Rakon part number FREQUENCY CHARACTERISTICS Test Condition Frequency Calibration tolerance Reflow shift Frequency stability over temperature Temperature range Frequency perturbations Short term stability Long term stability Long term stability G-Sensitivity Frequency offset after acceleration event Frequency at 25°C ±2°C and specified load capacitance Two consecutive reflows as per attached profile after 4 hours recovery at 25° Referenced to frequency reading at 25°C and the specified load capacitance Operating temperature Peak-to-peak deviation from the frequency vs. temperature 5th order curve fit. Minimum of 1 frequency reading every 3°C, over the operating temperature range Root Allan Variance for 1 second Tau Frequency drift over 1 year Frequency drift over 10 years Gamma vector of all three axes from 30Hz to 1500Hz. Values as low as 0.2ppb/G available depending on design (Note 1) 20,000G/2ms acceleration event in the z axis. Theoretical recovery time of 100ms (Note 1) Unit MHz ppm ppm ppm °C ppm ppb ppm ppm ppb/g ppm

Parameter Load capacitance (CL) Shunt capacitance (C0) Pullability Drive level Equivalent series resistance (ESR). Fundamental Insulation resistance (IR) Test Condition Frequency is calibrated at room temperature. Operating specification Operating specification Unit pF pF ppm/pF |jW n Mn Line Parameter Description Half sine-wave acceleration of 3,000G peak amplitude for 0.3ms duration, 3 cycles in each plane 10G RMS 30Hz to 1500Hz duration of 2 hours in each axis After 48 hours at 85°C 85% relative humidity non-condensing Exposed at -40°C for 30 minutes then to 85°C for 30 minutes constantly...

| MODEL COORDINATE ORIENTATION BOTTOM VIEW TITLE: RGX-3 MODEL RELATED DRAWINGS: Millimetres [inch]

-Rakon Mark -Rakon Product Code Date Code for Crystal FYMD _Crystal Date Code (see the Date Code chart) Crystal Month Code (see the Month Code chart) — Year Code (see the Year Code chart) RAKON Internal Code Y-Year Code Code Year Code Year Code Year Code Month Code Date Code Date Code Date January February March April May June July August September October November December Note: 1 MUST BE DIFFERENT TO I. TITLE: RSX-6, RS(G)X-5, RS(G)X-3 SERIES LID MARKING RELATED DRAWINGS: rakon Millimeters [inch]

TITLE: RSX-3/RGX-3 SERIES TAPE & REEL RELATED DRAWINGS: TOLERANCES: XX = XX = ±0.2 X.XX = ±0.10 X.XXX = X° = Hole = rakon © 2009 Rakon Limited

REEL DETAIL (SCALE 1 : 2.5) TITLE: RSX-3/RGX-3 SERIES TAPE & REEL RELATED DRAWINGS: rakon © 2009 Rakon Limited

NOTE: The product has been tested to withstand the Reflow Profile shown. The Reflow Profile used to solder Rakon RSX/RGX crystals are determined by the solder paste Manufacturer's specification. It is recommended that the Reflow Profile used does not exceed the one shown above. TITLE: RSX/RGX CRYSTAL Pb-FREE REFLOW RELATED DRAWINGS: SCALE: NTS rakon © 2009 Rakon Limited