Catalogs >
Rakon >
Low Noise Oscillator series LNO 3200 B3

Low Noise Oscillator series LNO 3200 B3
5Pages

Catalog excerpts

Low Noise Oscillator series LNO 3200 B3 - 1

Low Noise Oscillator series LNO 3200 B3 OCSO @ 3200 MHz Specific request can be addressed to RAKON hirel@rakon.fr Product Description LNO 3200 B3 is a low noise oscillator generating an output signal at 3200 MHz. It is composed by an OCSO (Oven Controlled SAW Oscillator) at 320 MHz fundamental frequency, followed by a frequency multiplier x10. It can optionally include a PLL to be phase locked on an external 10MHz reference. LNO 3200 B3 is designed for routine environment (test equipment, shelter, ground based military equipment ...). It is available in a 120.7mm x 76.2mm x 23.3mm package. Features Excellent phase noise performance (typical values) :  -130 dBc/Hz @ 1 kHz offset  -154 dBc/Hz @ 10 kHz offset  -157dBc/Hz noise floor Instrumentation (test equipment, simulator) Ground based military equipment as per MIL-PRF-28800F, Class 3 Clock for high speed ADC Rakon reserves the right to modify herein specifications and information when necessary to provide optimum perform

Open the catalog to page 1

Low Noise Oscillator series LNO 3200 B3 - 2

rakon Low Noise Oscillator series Technical Description LNO 3200 B3 is available in two different versions : • Standard version : in this case, it is a VC-OCSO (Voltage Controlled, Oven Controlled SAW Oscillator) that can be used either in free run mode, or controlled by an external DC voltage. • PLL version : in this case, the unit needs an external 10 MHz reference to operate, and the output signal is phase-locked to this reference. Standard version block diagram Power Mfit PLL version block diagram Lock Status . Rakon reserves the right to modify herein specifications and information...

Open the catalog to page 2

Low Noise Oscillator series LNO 3200 B3 - 3

Low Noise Oscillator series LNO 3200 B3 OCSO @ 3200 MHz Specifications 1.0 Environmental conditions Operating temperature range Storage temperature range As per MIL-PRF-28800F, Class 3, test equipment Random vibration As per MIL-PRF-28800F, Class 3, test equipment Test Condition Electrical interface Test Condition Operating Range Absolute Maximum Supply voltage Load impedance Control input voltage Control input impedance Reference input frequency Reference input level Pin 1, sine wave, 50  source and load Lock status Open drain Test Condition Nominal output frequency Output power Sine wave...

Open the catalog to page 3

Low Noise Oscillator series LNO 3200 B3 - 4

Low Noise Oscillator series LNO 3200 B3 OCSO @ 3200 MHz 3.9 Steady state power consumption Warm-up power consumption Warm-up time 9 1 ppm with reference to frequency reached after 1 hour of continuous operation Loop bandwidth Steady state power consumption Warm-up power consumption Warm-up time Single side band phase noise (PN) and time jitter Test Condition PN power density @ 1 kHz offset PN power density @ 10 kHz offset PN power density @ 1 MHz offset Harmonic distortion Other than harmonic distortion Full offset range jitter Broadband jitter Static conditions, at 25°C (guaranteed values...

Open the catalog to page 4

Low Noise Oscillator series LNO 3200 B3 - 5

Low Noise Oscillator series LNO 3200 B3 OCSO @ 3200 MHz 5.0 Mechanical features Outline in mm, nominal values (general tolerances : 0.15mm). Standard version : DC control voltage input PLL version : 10 MHz reference input Mechanical and electrical ground (-) Standard version : not used PLL version : Lock status Lock OFF -> ‘0’ Lock ON -> ‘HiZ’, pull-up limited to 3.6V Mechanical and electrical ground (-) Rakon reserves the right to modify herein specifications and information when necessary to provide optimum performan

Open the catalog to page 5

Low Noise Oscillator series LNO 3200 B3 5Pages

Catalog excerpts

All Rakon catalogs and technical brochures

Low Noise Oscillator series LNO 3200 B3
5Pages