adio Ultra Low Power sub 1GHz Multichannels Radio Transceiver The RC-CC1310-915-H module is based on Texas Instruments CC1310F128 component. This device combines a flexible, very low power RF transceiver with a powerful 48 MHz Cortex M3 microcontroller in a platform supporting multiple physical layers and RF standard. Sub-1Ghz technology is becoming one of the chief driving forces behind the Internet of Things (Iot), in particular this type of module is ideal for this applications basically for the following reasons : Ultra low power consumption, the consumption of this device is 5.5mA when receiving and 23.5mA when transmitting,in sleep mode the consumption is 0.6^A (microamps). Long range operations, the sensitivity parameter is -110dBm at data rates of 50 kbps and down to -124dBm when the data rate is 0.625kbps. Interference from other wireless communications can be overcome with 90dB of blocking. All this ensure a robust signaling for long range communications. SimpleLink-Easylink compatibility,ultra-low power platform designed (from TI) to easily implement the long-range connectivity with low power consumption on the Internet of Things projects (loT). TI-15.4 Stack, IEEE802.15.4e/g Standard Based Star Networking Software Designed for long range & robust star networks. 6LoWPAN compatibility with mesh network stack for Contiki. Applications: Feature: - Low-Power Wireless Systems - IEEE 802.15.4g mode switch support - Smart Grid and Automatic Meter Reading - Ultra Low consumption technology - Home and Building Automation - Powerful ARM Cortex M3 - Wireless Sensor Network - Supported by the open platform Contiki 6LoWPAN. - 6LoWPAN systems - Very Small size Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for Pa9- 1 / 10 any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

(*) Programmable parameter. - 128KB of On-System Programming Flash - 8KB of SRAM for Cache (or as General-Purpose RAM) - 20KB of Ultralow Leakege SRAM - Support Over-the-Air Upgrade (OTA) For more information and details, please refer to the CC1310 Texas Instruments datasheet.

adio ontrolli Wireless Modules Reference Schematics Mechanical Dimension r(2 .50 mm)Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for Pag- 3 / 10 Rev 2.5 any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

Antenna connection - Antenna connection trought hole and pad Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

adio fft ontrolli Wireless Modules To make immediate usable the RC-CC1310-915-H module with TI development systems has been realized the following board adapter. Adapter board front Texas Instruments Launchpad Connection Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

Recommended Hardware design1) Hardware All unused pins should be left floating; do not ground. All GND pins must be well grounded. Traces should not be routed underneath the module. The transceiver module must be powered from a regulated voltage. It is recommended to keep the power supply line for VCC as short and low impedence as possible. Near the power pins it is recommended to insert a ceramic the decoupling capacitor (100nF). It is recommended to have a copper ground plane under the shielded zone of the module. The ground plane should be unbroken. Board Ground Plane The antenna on the PCB...

ontrolli Wireless Modules Recommended Reflow Profile for Lead Free Solder Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

ontrolli Wireless Modules FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment...

Radio Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01 2.2 List of applicable FCC rules CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter 2.3 Specific operational use conditions This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. 2.4 Limited module...