adio Ultra Low Power sub 1GHz Multichannels Radio Transceiver The RC-CC1310-XXX module is based on Texas Instruments CC1310F128 component. This device combines a flexible, very low power RF transceiver with a powerful 48 MFIz Cortex M3 microcontroller in a platform supporting multiple physical layers and RF standard. Module Information : Sub-1Ghz technology is becoming one of the chief driving forces behind the Internet of Things (lot), in particular this type of module is ideal for this applications basically for the following reasons : Ultra low power consumption, the consumption of this device is 5.5mA when receiving and 23.5mA when transmitting at +14dBm (13.4mA at +10dBm) in sleep mode the consumption is 0.6pA (microamps). Long range operations, the sensitivity parameter is -110dBm at data rates of 50 kbps and down to -124dBm when the data rate is 0.625kbps. Interference from other wireless communications can be overcome with 90dB of blocking. The RF output power levels can reach up to +14dBm. All this ensure a robust signaling for long range communications. SimpleLink-Easylink compatibility,ultra-low power platform designed (from TI) to easily implement the long-range connectivity with low power consumption on the Internet of Things projects (loT). TI-15.4 Stack, IEEE802.15.4e/g Standard Based Star Networking Software Designed for long range & robust star networks. 6LoWPAN compatibility with mesh network stack for Contiki. Applications: Feature: - Low-Power Wireless Systems - IEEE 802.15.4g mode switch support - Smart Grid and Automatic Meter Reading - Ultra Low consumption technology - Home and Building Automation - Powerful ARM Cortex M3 - Wireless Sensor Network - Supported by the open platform Contiki 6LoWPAN. - 6LoWPAN systems - Very Small size Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for Pa9- 1 / 9 any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

(*) Programmable parameter. - 128KB of On-System Programming Flash - 8KB of SRAM for Cache (or as General-Purpose RAM) - 20KB of Ultralow Leakege SRAM - Support Over-the-Air Upgrade (OTA) For more information and details, please refer to the CC1310 Texas Instruments datasheet. Block Diagram

adio ontrolli Wireless Modules Reference Schematics Mechanical Dimension 15mm .50 mm)Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for Pag- 3 / 9 Rev 2.4 any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

adio Terminal description RC-CC1310-XXX Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

ontrolli Wireless Modules Type of Antenna connection Chip selector Difference between standard version and «H» version - With UFL Connector - Antenna connection to the UFL connector Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice. - Without UFL Connector - Antenna connection to hole and pad

adio RC-CC1310-XXX Adapter board To make immediate usable the RC-CC1310-XXX module with TI development systems has been realized the following board adapter. Adapter board front Adapter board rear SMART RF06 Evaluation board (TI) Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for Pag- 6 / 9 any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

Recommended Hardware design1) Hardware All unused pins should be left floating; do not ground. All GND pins must be well grounded. Traces should not be routed underneath the module. The transceiver module must be powered from a regulated voltage. It is recommended to keep the power supply line for VCC as short and low impedence as possible. Near the power pins it is recommended to insert a ceramic the decoupling capacitor (100nF). It is recommended to have a copper ground plane under the shielded zone of the module. The ground plane should be unbroken. Board Ground Plane The antenna on the PCB...

Wireless Modules Recommended Reflow Profile for Lead Free Solder 250 Soiling Zune Heating time Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.

adio REEL DIMENSIONS L Reel Width (45mm) Radiocontrolli s.r.l refuses any responsibility for irregular uses of the devices and for any possible lack or inaccuracy of the data and reserves the right to change in whole or in part these information without notice.