Group: Elecon Engineering Group
Catalog excerpts
with you at every turn
Open the catalog to page 1PRODUCTS IN THE RANGE Serving an entire spectrum of mechanical drive applications from food, energy, mining and metal; to automotive, aerospace and marine propulsion, we are here to make a positive difference to the supply of drive solutions. Series A Worm Gear units and geared motors in single & double reduction types Series BD Screwjack worm gear unit Series BS Worm gear unit Series C Right angle drive helical worm geared motors & reducers Series F Parallel angle helical bevel helical geared motors & reducers Series G Helical parallel shaft & bevel helical right angle drive gear units...
Open the catalog to page 2Couplings Our range ofcouplings have been proven to be some ofthe most reliable, durable and effective couplings in the marketplace. These qualities have been achieved by our attention to detail in design, manufacturing capabilities and application expertise. This ensures our coupling range is capable of providing solutions for a wide and varied range of applications and installations. Elign Gear Couplings The Elign range of gear couplings not only connect two rotating shafts, but also accommodate the inevitable misalignment that can occur in installations. The Elign gear coupling is...
Open the catalog to page 3Mechanical Ratings and Service Factor The mechanical ratings are a measure ofthe couplings capacity in terms of life and strength, they assume 10 hours/day operation under uniform loading conditions and allow for a 100% momentary overload at starting or braking The mechanical Service Factor (fm) is selected dependant on the type of prime mover, the classification ofthe driven load, and duration ofoperation i) Obtain the driven load classification type from the table Load Classification by Application ii) Determine the mechanical service factor from the table below: Kev to symbols: P = Power...
Open the catalog to page 4Load Classifications - U =Uniform Load M =Moderate Shock Load H =Heavy Shock Load t =Consult our Engineers Agitators Pure liquids Liquids and solids Liquids variable density Blowers Centrifugal Lobe Vane Brewing & distilling Bottling machinery Brew Kettles Cookers Mash tubs Scale hopper Elevators Bucket - Uniform load Bucket - Heavy load Bucket - Continuous Centrifugal discharge Escalators Freight Gravity discharge Passenger lifts Fans Centrifugal Cooling towers Induced draft Forced draft Fan - Large diameter induced draft Fan - Light, small diameter Can filling machinery Crane knife Car...
Open the catalog to page 5Coupling Size Coupling Types ELIGN - Geartypecouplings ELIGN Double engagementwith Flange ELIGN Single engagementwith Flange ELIGN Double engagementwith Spacertube ELIGN Double engagement forvertical operation ELIGN Fully Rigid Coupling ELIGN Double engagementwith Continuous sleeve EFC | ELFLEX - Pin and Bush type flexible Couplings EFC - ELFLEX Standard Coupling FC | FC - ELFLEX Standard Coupling - Larger size FBC | FBC - ELFLEX Coupling with integral Brake drum Bore Types | A | American Parallel Keyway(USAS B17.1:1967) | M | Metric Bore parallel keyway (DIN6885/1) | T |...
Open the catalog to page 6GEAR TYPE COUPLINGS
Open the catalog to page 7The ELIGN Gear Couplings consist of hubs with multi crowned teeth at the flank, tip and chamfer. The ELIGN hub teeth are manufactured using the latest state of the art CNC machines, and are manufactured from quality forged carbon steel, and are subjected to a number ofquality checks and tests. The superior design ofthe multi- crowned tooth profile enables the ELIGN gear coupling to operate satisfactorily under all operating conditions with increased reliability and durability. The multi- crowned teeth are tolerant to misalignment whilst improving the load carrying capacity and minimising...
Open the catalog to page 8Gear Couplings Gear Coupling are used to join two rotating shafts for efficient transmission of mechanical power. Although the shafts can be accurately aligned at the time of installation, it is likely that during the operation the alignment may get disturbed due to settling ofthe foundation, thermal expansion, shaft deflection, wearing out of other parts, improper maintenance or many other reasons. Due to unavoidable misalignment occurring during operation a Gear Coupling provides An ideal solution to compensate or minimise the effect of misalignment. Gear Couplings are therefore ideally...
Open the catalog to page 9Lifting Hole The hubs of larger size couplings are supplied with lifting holes, as indicated on the dimension sheets. Lubrication Each coupling half is provided with a grease nipple / plug from where grease can be filled directly. WARNING: Grease should be applied Protection All components of ELIGN gear couplings have a rust preventative coating. Coupling Bores Standard parallel keyways conform to USAS B17.1 1967 and hubs are bored to suit the customers shaft size (see dimension tables for the minimum / maximum allowable bore) standard metric keyways conform to DIN-6885, PART-1 (unless...
Open the catalog to page 10COUPLINGS NOTES
Open the catalog to page 20FLEXIBLE PIN AND BUSH COUPLING
Open the catalog to page 21ELFLEX Flexible couplings transmittorque from one shaftto another and are particularly useful in cases where a limited amount of misalignment ofthe shafts is unavoidable. ELFLEX flexible couplings are cushioned drive pin and bush type couplings that transmits the torque through rubber bushes which have an excellent capacity to absorb shock loads. The flanges are manufactured from high quality cast iron and are suitable for speeds up to the maximum limits as listed in the dimension tables. FEATURES OF ELFLEX FLEXIBLE COUPLINGS Permits drive in either direction and are suitable for driving...
Open the catalog to page 22Elflex Couplings Type EFC
Open the catalog to page 23GEAR COUPLINGS WITH NYLON SLEEVE
Open the catalog to page 27General Description Nylicon flexible gear couplings, types X600, are available in three sizes and are ideal for small power drives with bore sizes up to 2.25 inches (55mm) diameter and a basic rated torque up to 342 Lb.ft Uniform Loading Thermosetting plastic sleeves provide non conductive assemblies. Staggered internal teeth ensure uniform loading and an internal central buffer ring between the two hubs promote axial location giving protection to the gear teeth. Low Cost Option They compensate for all types of shaft misalignment and allow a small amount of end float. Nylicon couplings are...
Open the catalog to page 28All Radicon catalogs and technical brochures
-
Series X Flexible Couplings
36 Pages
-
Series M Helical In-Line
116 Pages
-
BR-Series-AM.
72 Pages
-
adicon-SeriesX
32 Pages
-
BR Series F
117 Pages
-
BR Series X Couplings
36 Pages
-
BR Cone Ring Couplings
16 Pages
-
Series J
73 Pages
-
Motor
4 Pages
-
Series E Flyer
4 Pages
-
G series
4 Pages
-
BD
4 Pages
-
Product Brochure radicon
8 Pages
-
Benzlers Screw Jacks
69 Pages
-
Series J - Shaft Mounted Gearbox
15 Pages
-
Series X Flexible Couplings
20 Pages
-
Radicon Series ET
42 Pages
-
BR Series G
71 Pages
-
Metric
8 Pages
-
Geared Pump
15 Pages
-
Series P Planetary
4 Pages
-
M series
120 Pages
-
Sala Gears
74 Pages
-
Roloid Pump
17 Pages
-
Heavy Duty Worm Gear Series ER
15 Pages
-
Screw Jacks
58 Pages
-
Series AM Worm Gear
73 Pages
-
Worm Gear Series AJ
89 Pages
-
Series BS Worm Gear
60 Pages
-
Elflex Flexible Couplings
8 Pages
-
Series H industrial gearboxes
123 Pages
-
SERIE G
71 Pages
-
C series
120 Pages
-
Geared Motor Series K
90 Pages
-
F series
119 Pages
-
Elign Gear Couplings
17 Pages
Archived catalogs
-
Series X Flexible Couplings
33 Pages
-
Worm Gears Series AH
13 Pages