SEMI AUTO CARTON SEALER MACHINE

SAFETY RULES (^MJ'J) 3 TECHNICAL DATA (S^gM) 4 PNEUMATIC DIAGRAM _ 5. TAPPING HEAD ASSEMBLY _ 7. SIDE DRIVEN ASSEMBLYiM^^ 9. GRIP & KNOCK BAR ASSEMBLYa&jftffA

PREFACE (前言) We are pleased that you have chosen the FXJ-AT5050 automatic sealing machine, the structure of this machine is quite solid, and also can be easily to perform maintenance work. To get the higher efficiency, please read the manual carefully before staring the machine. SAFETY RULES （安全规则） The machine can not be operated by untrained personal. 这台机器不能让未经培训的个人操作。 Please observe all the precautions and warning labels. 请遵守所有的预防措施和警告标签。 Do not remove or make any changes of the safety device. 不要拆卸或进行任何更改的安全装置。 When the machine is operating, do not make other maintainess or repair works当机器运作时,不要进行维修工作...

INSTALLATION 安装 ※ The power supply system, votage and frequency must correspond to the regulation label attached to the machine. 电源系统、电压和频率必须对应监管标签附加到这台机器。 ※ Connect the plug. 插头连接 ※ Operate the machine by the side switch. 通过侧开关操作这台机器的。 NOTICE: 注意 Please install the machine where a power supply can be easily connected. It is necissary to disconnect the power supply plug prior to open the control box’s cover. 断开电源插头之前打开控制箱的封 面这是十分有必要的 ADJUSTMENT 调试 Screw调整旋钮 Fixed nut 固定螺母 Brake 刹车轮 Stopper 止动器 Outer leg Adjustable leg Screw Pressure indicator 压力指示器 Oil tank 油箱 Water Filter 滤水器 NOTICE: Before...

Height adjustment crank Step3: Height adjustment 第三步:调整高度 (1) Put a carton on the table. 把一个纸箱放在桌子上。 (2) Rotate the height adjustment crank to adjust the table height. 旋转高度调节曲柄,调整桌子的高度。 (3) The front guide plate just need to be adjusted to touch the carton top. 前导流板要调整到碰纸箱顶部 Side pressure handle Conveyer belt Side roller Width adjustment crank (1) Rotate the width adjustment crank, the width just needs to be adjusted to clamp the carton properly and let it can be welled pass through. 旋转宽度调整曲柄,宽度需调整到将纸箱正确夹紧,以便纸箱可以顺利通过。 (2) Loose the handle o

Thread illustration 线程图解 Glue Side Glue Side Upper tape head Lower tape head MAINTENANCE AND LUBRICATION 保养和润滑 Please read the instruction manual prior to perform maintenance and inspection works. Before performing maintenance work, please shout down the machine and disconnect the power supply, it is an important step to avoid missend the electricity. ※ If it is necessary to use the different specification of tape, please refer to the part list in this manual. ※ Periodically clean the grime, dust and dirt stuck on the belt and clean up any other parts of the machine. ※ To extend the blade longevity,...

PNEUMATIC CONTROL DIAGRAM FILTER 滤波器 SOLENOID VALVE 电磁阀 CYLINDER 40*150

TROUBLE SHOOTING 故障排除 Fault The carton width is too narrow. Please use the appropriate size of the carton. The belt was worn Replace a new belt The carton can not be transported by the side driven belt The driven belt will not move. The pressure of the upper tape Adjust the upper tape head’s head is not enough. height. Upper tape head’s roller is Adjust the roller position. positioned too low. The upper tape head’s spring Loosen the spring to reduce the tension. is too tight. The belt’s tension is not strong Adjust the belt’s tension. enough. The power is not being connected. The motor will not...

Part list

TAPPING HEAD ASSEMBLY

TAPPING HEAD ASSEMBLY

TAPPING HEAD ASSEMBLY

FRAME ASSEMBLY

FRAME ASSEMBLY

SIDE DRIVEN ASSEMBLY

SIDE DRIVEN ASSEMBLY

MAST ASSEMBLY

MAST ASSEMBLY

GRIP & KNOCK BAR ASSEMBLY

GRIP AND KNOCK BAR ASSEMBLY