TAKHI-series User Manual Fiber coupled Halogen Light Source VIS-NIR Pyroistech S.L. Edificio I+D Jerónimo de Ayanz Campus Arrosadía 31006, Pamplona, Spain +34 698 91 04 12 www.pyroistech.com [email protected] © 2020 Pyroistech

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission from Pyroistech S.L. This manual accompanies a product order and is subjected to the condition that it shall not, by way of trade or otherwise, be lent, re-sold, hired out or otherwise circulated without the prior consent of Pyroistech S.L. in any form of binding or cover other than that in which it is published. The specifications indicated in this manual are subject to change...

www.pyroistech.com [email protected]

0. Introduction Thank you for purchasing this TAKHI light source from Pyroistech.SL. This document describes the TAKHI light source and provides you with instructions for its correct operation. Please do not hesitate to contact us through [email protected] if you have any questions or doubts about this manual. The TAKHI series comprises high power halogen light sources with a spectrum that range from VIS to NIR (350-2250nm). They are conceived as user friendly, compact tools and being ideal for spectroscopy and general optical fiber illumination applications. These light sources have been designed...

1. Technical Specifications Pyroistech counts with 2 models of its TAKHI halogen light source: TAKHI-HP (more powerful) and TAKHI MP (longer lifetime). The specifications of both models are: Optical characteristics Light bulb specifications Output connector Spectral range Luminous Flux Lamp holder Typical optical power output (1) (1) Measured with an optical fiber (core Ø 600µm) and a Si photodiode (OPHIR™ ) (2) To get replacement light bulbs, contact us through [email protected] Other characteristics Electrical characteristics Connector type Stabilization time Input Current Input Voltage AC/DC...

2. Operation 2.1 Package Content • Requested TAKHI light source • Power source: input 100 - 240 V~, 50 - 60 Hz; output 12 V, 5.5 A; 99 x50 x33 cm, cord length 1.5 m. • Power cord 1.85 m long • User’s manual Inspect carefully the devices and make sure there is no damage. On the contrary, do not employ the light source and please contact us through [email protected] for repair or replacement information. 2.2 Operating instructions Insert the plug of the power cord into the power supply and connect the power cord to the power outlet. Then, introduce the plug of the power supply into the light...

3.2 Light bulb replacement To replace the light bulb when it has ended its life cycle, the following process must be done carefully. 1) Disconnect the power source. Wait for 2) Remove the screws using an allen key the light source to cool down if it is hot. Nº2.5 and remove the top cover carefully without pulling the fan cables. 3) Remove the screws using an allen key 4) Carefully remove the bulb using Nº2 in order to have access to the inner tweezers. Install the new bulb (*) without box cover. touching it with bare hands. To reassemble, repeat the process in reverse order. (*) To ensure maximum...

4. Important Notes Before operation • Do not remove or alter any installed safety device on this equipment. Doing so will cancel your warranty and create an unsafe operating environment. • There are NO user serviceable parts inside. Dangerous currents are present in this device. Only allow qualified personnel to service this unit. • Inspect this unit and its power supply before using it for the first time. Do not use the unit if it is damaged in any way. Contact us for repair or replacement information. During operation • Do not cover the source or obstruct the air flow for its refrigeration....

4. Warranty Pyroistech’s general warranty for a product has a 1 year duration. This warranty includes repairs and replacement of damaged parts due to a malfunction of the source, as long as said malfunction can be attributed to errors made in the manufacture of it by Pyroistech SL, not to a punctual misuse of the source or to a continued incorrect employment of it by the user, whether conscious or unconscious, due to not having followed the operation recommendations indicated by Pyroistech SL There is the possibility of extending this guarantee. For more information, contact Pyroistech S.L. 5....

First Document www.pyroistech.com [email protected]

PYROISTECH S.L. Edificio I+D Jerónimo de Ayanz Campus Arrosadía 31006, Pamplona, Spain +34 948 168 845 Email: [email protected]