User Manual Fiber coupled LED light source UV-VIS-NIR Pyroistech S.L. Edificio I+D Jerónimo de Ayanz Campus Arrosadía 31006, Pamplona, Spain +34 698 91 04 12 www.pyroistech.com [email protected] © 2020 Pyroistech

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission from Pyroistech S.L. This manual accompanies a product order and is subjected to the condition that it shall not, by way of trade or otherwise, be lent, re-sold, hired out or otherwise circulated without the prior consent of Pyroistech S.L. in any form of binding or cover other than that in which it is published. The specifications indicated in this manual are subject to change...

Table of Contents 0. Introduction……………………………...…………………… 5 1. Technical Specifications……………………………...……. 5 2. Operation………………………………………...……………. 6 2.1 Package Content………………………………………………………………………….. 6 2.2 Before use……………………………………………………………………………………. 6 2.3 Maintenance……………………………………………………………………

www.pyroistech.com [email protected]

0. Introduction Thank you for purchasing this COB light source from Pyroistech.SL. This document describes the COB light source and provides you with instructions for its correct operation. Please do not hesitate to contact us through [email protected] if you have any questions or doubts about this manual. The COB series comprises high power LED light sources with peak wavelengths that range from UV to NIR (270 – 1050 nm). They are conceived as user friendly, compact and silent tools, being ideal for fluorescence, spectroscopy and general optical fiber illumination applications. These light...

Other characteristics Electrical characteristics Power input Signal input for pulsed mode Connector type Connector type Output connector Stabilization time 2. Operation 2.1 Package Content • Requested COB light source • Power source: input 100 - 240 V~, 50 - 60 Hz; output 18 V, 2 A; 99 x50 x33 cm, cord length 1.5 m. • Power cord 1.85 m long • User’s manual Inspect carefully the devices and make sure there is no damage. On the contrary, do not employ the light source and please contact us through [email protected] for repair or replacement information. 2.2 Before use Insert the plug of the power...

Intensity regulator (20% - 100%) in CW mode Power input www.pyroistech.com [email protected]

2.5 Operation Modes The controls feature a three way switch (3) to select the operation mode: continuous, pulsed or off. A second control (1) is used to manually adjust the drive current in continuous mode. A connector allows (4) to introduce a control signal in the PWM mode. • OFF mode The switch (3) on the right of the frontal face of the light source has to be on the middle position (‘OFF’). It is suggested to have the switch in this position when connecting the power supply to the light source through (5). • CW mode To select the continuous mode, please move the switch (3) to the left position...

3. Important Notes Before operation • Do not remove or alter any installed safety device on this equipment. Doing so will cancel your warranty and create an unsafe operating environment. • There are NO user serviceable parts inside. Dangerous currents are present in this device. Only allow qualified personnel to service this unit. • Inspect this unit and its power supply before using it for the first time. Do not use the unit if it is damaged in any way. Contact us for repair or replacement information. During operation • Do not cover the source or obstruct the air flow for its refrigeration....

Electromagnetic Compatibility • Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of this equipment. Otherwise, degradation of the performance of this equipment could result. • The use of cables, power supplies, transformers and accessories other than those specified by Pyroistech S.L., in addition to not being covered by the warranty, may lead to increased emissions and/or decreased electromagnetic compatibility. 4. Warranty Pyroistech’s general warranty for a product has a 1 year...

First Document www.pyroistech.com [email protected]

PYROISTECH S.L. Edificio I+D Jerónimo de Ayanz Campus Arrosadía 31006, Pamplona, Spain +34 698 91 04 12 Email: [email protected]