*mydirectindustry

PVD3SDN

Product catalog summary

Overview: The PVD3SDN is a proportional valve driver designed for direct DIN solenoid mounting with a DIN cable connector. It features a sealed design, simple control via two digital inputs, and a robust housing made from flame-retardant plastic.

Benefits and Features: The device offers versatile digital design, easy adjustments with a three-digit LED display, a wide supply voltage range, and an energy-efficient PWM circuit. It is protected against incorrect connections and short circuits, and it maintains output despite changes in supply voltage and coil resistance.

Specifications: Operating voltage ranges from 9 to 35VDC, with a maximum output current of 3A. It supports ramp times from 0.0 to 99.5 seconds, a linearity of 0.5%, and PWM/dither frequencies between 50-500Hz. The operating temperature range is -40° to +75° Celsius, and it has an IP67 protection grade.

Compliance: The product meets the essential requirements of the EMC Directive 2004/108/EC, including standards EN61000-6-1:2005 and EN61000-6-3:2006.

Settings and Range: The device includes settings for jog simulation, set points (P1 to P4), ramp up/down times, dither frequency, and display orientation. Settings can be saved or discarded upon power down.

Set-Up Procedure: Users can enter set-up mode to adjust settings, which are immediately effective. To save changes, rotate the control until 'SA' is displayed and then rotate one full turn.

Wiring Diagrams: The document includes wiring diagrams with a note to avoid connecting a specific pin to ground.

Catalog excerpts

Proportional Valve Driver, direct DIN solenoid mount, DIN cable connector Versatile digital design Large, easy-to-use adjustments and three-digit seven-segment LED display Wide range of supply voltage Electronic limiting circuit / short circuit proof Load can be connected & disconnected live Protected against wrong connection Energy-efficient PWM circuit, no heat sink is required Current sensing maintains output regardless of changes in supply voltage and coil resistance Completely sealed even during set-up Simple control with two digital inputs Thick wall, sturdy housing made of flame retardant plastic UL94-V0 Mounting: DIN 43650-A/ISO 4400 for solenoid as well as cable connector Easy troubleshooting / cable length not an issue Operating voltage: 9 - 35VDC Maximum output current: 3A Ramp time: 0.0 to 99.5s Linearity: 0.5% PWM / Dither frequency: 50-500Hz Operating temperature: -40° to +75° Celsius Input signals: two digital (on/off) This product fulfills the essential requirements of the EMC Directive 2004/108/EC: EN61000-6-1:2005, EN61000-6-3:2006 PWM Controls Inc. | [email protected] | www.pwmcontrols.com tel +1 905 542 1245 | fax +1 866 591 3484

Open the catalog to page 1

Proportional Valve Driver, direct DIN solenoid mount, DIN cable connector Jog, used to simulate signal set point 1, 0.00 to 3.00 A set point 2, 0.00 to 3.00 A set point 3, 0.00 to 3.00 A set point 4, 0.00 to 3.00 A Ramp up, time required for the output to increase 1A, 00.0 to 99.5 s Ramp down, time required for the output to decrease 1A, 00.0 to 99.5 s Dither frequency, 050 to 500 Hz Display orientation, normal or up-side-down Save settings SET-UP PROCEDURE: At power up, you may rotate clockwise to read the actual solenoid output current directly in Amps or counterclockwise to read the target...

Open the catalog to page 2

Proportional Valve Driver, direct DIN solenoid mount, DIN cable connector PWM Controls Inc. | [email protected] | www.pwmcontrols.com tel +1 905 542 1245 | fax +1 866 591 3484

Open the catalog to page 3

Proportional Valve Driver, direct DIN solenoid mount, DIN cable connector WIRING DIAGRAMS: Proportional Ualve Driver Pouer Supply Proportional Ualve Driver NOTE: Do not connect pin © to ground PWM Controls Inc. | [email protected] | www.pwmcontrols.com

Open the catalog to page 4

All PWM Controls Inc. catalogs and technical brochures

Archived catalogs

PVD3D1R Proportional Valve Driver
3 Pages
PVD3D10 Proportional Valve Driver
4 Pages