*mydirectindustry

PVD3S3M

1 / 3 PagesView full catalog

PVD3S3M

Product catalog summary

Benefits and Features:

Versatile digital design with easy-to-use adjustments and a three-digit LED display.
Completely sealed design, even during setup, with a wide range of supply voltage.
Features an electronic limiting circuit that is short circuit proof and allows live connection and disconnection of loads.
Protected against incorrect connections and includes simple control with two digital inputs.
Energy-efficient PWM circuit that does not require a heat sink.
Current sensing maintains output regardless of supply voltage and coil resistance changes.
Sturdy housing made of flame retardant plastic (UL94-V0) with DIN 43650-A/ISO 4400 solenoid mounting for easy troubleshooting.

Specifications:

Operating voltage: 9 - 35VDC
Maximum output current: 3A
Ramp time: 0.0 to 99.5 seconds
Linearity: 0.5%
Protection grade: IP67 (when properly assembled with the included brown gasket)
Input signals: two on/off (digital)
PWM/Dither frequency: 50-500Hz
Operating temperature: -40° to +75° Celsius
Size: 2.5” long (3.5” with cable gland) x 1.5” wide x 1.4” deep

Compliance:

Fulfills the essential requirements of the EMC Directive 2004/108/EC: EN61000-6-1:2005, EN61000-6-3:2006

Settings and Range:

J9 Jog: Used to simulate signal
P1 to P4 set points: 0.00 to 3.00 A
Ramp up/down time: 00.0 to 99.5 seconds
Dither frequency: 050 to 500 Hz
Display orientation: Normal or upside-down
SA: Save settings

Set-Up Procedure:

At power-up, rotate clockwise to read the actual solenoid output current in Amps or counterclockwise to read the target set point. Enter set-up mode by rotating; the display will show settings sequentially. Modify settings by rotating up or down to the desired value. To save new settings, rotate until the display shows SA and then rotate one full turn. To discard changes, power down without saving.

Wiring Examples:

Illustrates the configuration of I/O1 and I/O2 for different set points (P1, P2, P3, P4).

Catalog excerpts

PVD3S3M, Proportional Valve Driver, direct DIN solenoid mount, 3m cable 4 x AWG18 BENEFITS AND FEATURES: • • Versatile digital design Large, easy-to-use adjustments and three-digit seven-segment LED display Completely sealed even during set-up Wide range of supply voltage Electronic limiting circuit / short circuit proof Load can be connected & disconnected live Protected against wrong connection Simple control with two digital inputs Energy-efficient PWM circuit, no heat sink is required Current sensing maintains output regardless of changes in supply voltage and coil resistance Thick wall, sturdy housing made of flame retardant plastic UL94-V0 Mounting: DIN 43650-A/ISO 4400 solenoid Easy troubleshooting Operating voltage: 9 - 35VDC Maximum output current: 3A Ramp time: 0.0 to 99.5s Linearity: 0.5% Protection grade: IP67** Input signals: two on/off (digital) PWM / Dither frequency: 50-500Hz Operating temperature: -40° to +75° Celsius Size: 2.5” long (3.5” with cable gland) x 1.5” wide x 1.4” deep ** when properly assembled using the brown gasket (included in the package) between solenoid and driver This product fulfills the essential requirements of the EMC Directive 2004/108/EC: EN61000-6-1:2005, EN61000-6-3:2006 PWM CONTROLS INC. | 1205 WALNUT ST, VICTORIA, BRITISH COLUMBIA CANADA V8T 1N3 tel +1 905 542 1245 fax +1 866 591 3484 pwmcontrols.com

Open the catalog to page 1

PVD3S3M PVD3S3M, Proportional Valve Driver, direct DIN solenoid mount, 3m cable 4 x AWG18 SETTINGS AND RANGE: Jog, used to simulate signal set point 1, 0.00 to 3.00 A set point 2, 0.00 to 3.00 A set point 3, 0.00 to 3.00 A set point 4, 0.00 to 3.00 A Ramp up, time required for the output to increase 1A, 00.0 to 99.5 s Ramp down, time required for the output to decrease 1A, 00.0 to 99.5 s Dither frequency, 050 to 500 Hz Display orientation, normal or up-side-down Save settings SET-UP PROCEDURE: At power up, you may rotate clockwise to read the actual solenoid output current directly in Amps or...

Open the catalog to page 2

PROPORTIONAL VALVE DRIVERS PVD3S3M, Proportional Valve Driver, direct DIN solenoid mount, 3m cable 4 x AWG18 WIRING EXAMPLES: Proportional Ualve Driver Pouer Supply Proportional Ualve Driver PWM CONTROLS INC. | 1205 WALNUT ST, VICTORIA, BRITISH COLUMBIA CANADA V8T 1N3

Open the catalog to page 3

All PWM Controls Inc. catalogs and technical brochures

Archived catalogs

PVD3D1R Proportional Valve Driver
3 Pages
PVD3D10 Proportional Valve Driver
4 Pages