AE30
12Pages

data sheet AE30 www.pwb-encoders.com Motion Control Solutions PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany Phone: +49 3691 72580-0 Fax: +49 3691 72580-29 info@pwb-encoders.com www.pwb-encoders.com PWB encoders Gm bH Am G oldberg 2 D-9981 7 E ise na ch Germa ny info@pwb-encode rs.com / www .pwb-encode rs.com

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Description The AE30 is a reliable low cost optical hollow shaft encoder that can be fixed quickly and easily on different sizes of motor shafts. The encoder provides two square wave outputs in quadrature (90 degrees phase shifted) and one optional index channel (one pulse per revolution). The resolution of the encoder is determined by the number of counts per revolution (CPR). Power supply and signals are provided by an 8 pin Molex connector. Main characteristics - Hollow shaft encoder High performance in compact size Robust...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Absolute maximum ratings Parameter Supply voltage Output voltage Output current Storage temperature Recommended operating conditions Encoding characteristics over recommended operating range and recommended mounting tolerances unless otherwise specified. Parameter Operating temperature Operating temperature Supply voltage Load capacitance Electrical characteristics Parameter Supply current 2 channel Supply current 3 channel High level output voltage Low level output voltage Output waveform rise time Output waveform fall time RL =...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Encoder characteristic Encoding characteristics over recommended operating range and recommended mounting tolerances unless otherwise specified. Parameter Pulse width error State width error Phase error Index pulse width Pulse width error State width error Phase error Note: M1/M2: see ordering codes Definitions Count (N): The number of bar and window pairs or increments per revolution (CPR) of the code wheel. One Cycle C: One period of the signal, related to 1 bar and 1 window. It is measured in electrical degrees, one cycle is...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Encoder header connector: Housing connector: Wennmacher CX-H-125-8 with CX-T125F terminals M1 Molex 51021-0800 with 50079-8000 terminals M2 Pin-out description Pin Output pin 1 red Index I+ green Not connected blue Channel B+ purple Not connected brown Channel A+ yellow Not connected white Ground black Power supply red green blue purple brown yellow orange black Note: M1/M2: see ordering codes & cable accessories PWB encoders Gm bH Am G oldberg 2 D-9981 7 E ise na ch Germa ny info@pwb-encode rs.com / www .pwb-encode rs.com

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Mechanical characteristics and drawings Parameter D imensions Weig ht Shaft diameters Ø Motor shaft length protrusion L Max. motor mounting b oss diameter D Max. motor mounting b oss height H Max. motor axial shaft play 9.5 (see Fig.2 belo w) 13.0 (see Fig.2 below) 2.0 (see Fig.2 belo w) Max. motor shaft ecce ntricity + radial pla y 2 X M3 (DIN 96 5) 3 X M2 (DIN 79 85) 15 Refer to Fi g.3 below IP50 (according to DIN 40 500)* PBT, 17% glass fibre re inforced UL 94 V-0 Screws for fixing Ti ghtening torque o f the screws Flange p ri...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions AE30 MOUNTING INSTRUCTION Align the base plate to the motor shaft by using the centering gauge Afterwards fix the base plate to the motor flange using two screws (M3) or three screws (M2) When the encoder fits totally onto the flange, start to rotate the encoder clockwiseO...O. Align the hole of the hub to the motor shaft and push the encoder until it will touch the flange OOOO until a stop point is reached After assembling the encoder on the flange, remove the stopper. PWB encoders Gm bH Am G oldberg 2 D-9981 7 E ise na ch Germa...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions AE30 MOUNTING INSTRUCTION Push the wall into the housing into its final position. Do not rotate the encoder after assembly or when it is in operation. Do not pull out the wall after assembly or when it is in operation. ATTENTION! The encoder is designed to be assembled only one time, otherwise the guarantee will be voided. Note: see IMPORTANT NOTICE (page 12) PWB encoders Gm bH Am G oldberg 2 D-9981 7 E ise na ch Germa ny info@pwb-encode rs.com / www .pwb-encode rs.com

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Available accessories Standard cable Cable 300 mm length UL 10002 / AWG28 with female housing connector: Wennmacher CX-H-125-8 with CX-T125F terminals M2 Cable 300 mm length UL1061 / AWG26 with female housing connector: Molex 51021-0800 with 50079-8000 terminals Note: M1/M2: see ordering codes Adapter cable Twisted adapter cable 500 mm length UL10002 / AWG28 with female housing connector: 8-pin Wennmacher connector (Wennmacher CX-H-125-8 Housing with CX-T125F terminals) to a 10-pin Molex connector (Molex 90142-0010 housing with...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Available accessories Customized adapter plate Centering gauge for different motor shafts PWB encoders Gm bH Am G oldberg 2 D-9981 7 E ise na ch Germa ny info@pwb-encode rs.com / www .pwb-encode rs.com

data sheet AE30 www.pwb-encoders.com Motion Control Solutions Ordering codes Output type Frequency range Tenperature range Connector version adapter cable ** w ith out cable C: side connector + standard cable ** Available accessories (no parts of standard delivery): - standard cable 300 mm length - adapter cable 500 mm length - adapter plates for different motors - centering gauge for different motor shafts (highly recommended for correct assembly) - fastening screws 3pcs DIN 7985 M2 X 8 - fastening screws 2pcs DIN 965 M3 X 8 PWB encoders GmbH RESTRICTED THIS DOCUMENT AND ANY ASSOCIATED...

data sheet AE30 www.pwb-encoders.com Motion Control Solutions IMPORTANT NOTICE The encoder is so designed that it may be assembled only one time, otherwise the guarantee will be voided. The guarantee will be voided by misuse, accident, modification, unsuitable physical or operating environment, operation in other than the specified operating environment, or failure caused by a product for which PWB encoders GmbH is not responsible. PWB encoders GmbH reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services also...