AE 30 F
11Pages

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany Phone: +49 3691 72580-0 Fax: +49 3691 72580-29 info@pwb-encoders.com www.pwb-encoders.com PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany info@pwb-encoders.com / www.pwb-encoders.com

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Description The AE30-F is a reliable low cost optical hollow shaft encoder that can be fixed quickly and easily on different sizes of motor shafts. The encoder provides two square wave outputs in quadrature (90 degrees phase shifted) and one optional index channel (one pulse per revolution). The resolution of the encoder is determined by the number of counts per revolution (CPR). Power supply and signals are provided by an 8 pin Molex connector. Main characteristics - Hollow shaft encoder High performance in compact size Robust...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Absolute maximum ratings Parameter Storage temperature Storage temperature Supply voltage Output voltage Output current Recommended operating conditions Encoding characteristics over recommended operating range and recommended mounting tolerances unless otherwise specified. Parameter Operating temperature Operating temperature Supply voltage Load capacitance Electrical characteristics Parameter Supply current 2 channel Supply current 3 channel High level output voltage Low level output voltage Output waveform rise time Output...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Encoder characteristic Pulse width error State width error Phase error Index pulse width Encoding characteristics over recommended operating range and recommended mounting tolerances unless otherwise specified. Parameter Pulse width error State width error Phase error Note: M1/M2: see ordering codes Definitions Count (N): The number of bar and window pairs or increments per revolution (CPR) of the code wheel. One Cycle C: One period of the signal, related to 1 bar and 1 window. It is measured in electrical degrees, one cycle is...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Encoder header connector: Housing connector: Wennmacher CX-H-125-8 with CX-T125F terminals M1 Molex 51021-0800 with 50079-8000 terminals M2 Pin-out description Pin Output pin 1 red Index I+ green Not connected blue Channel B+ purple Not connected brown Channel A+ yellow Not connected white Ground black Power supply red green blue purple brown yellow orange black Note: M1/M2: see ordering codes & cable accessories PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany info@pwb-encoders.com / www.pwb-encoders.com

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Mechanical characteristics and drawings Parameter Dimensions Weight Shaft diameters ØZ Motor shaft length protrusion L Max. motor mounting boss diameter ØD Max. motor mounting boss height H Max. motor axial shaft play Max. motor shaft eccentricity + radial play Screws for fixing Tightening torque of the screws Pitch circle diameter ØC Protection grade Plastic material (eccentricity decreases signal performances) 2 X M3 (DIN 965) 15 46 IP50 (according to DIN 40500)* PBT, 17% glass fibre reinforced UL 94 V-0 Note: * When the...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions AE30-F MOUNTING INSTRUCTION Align the base plate to the motor shaft by using the centering gauge Afterwards fix the base plate to the motor flange using two screws M3 When the encoder fits totally onto the flange, start to rotate the encoder clockwise…...…. Align the hole of the hub to the motor shaft and push the encoder until it will touch the flange ………… until a stop point is reached After assembling the encoder on the flange, remove the stopper. PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany info@pwb-encoders.com...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Push the wall into the housing into its final position. Do not rotate the encoder after assembly or when it is in operation. Do not pull out the wall after assembly or when it is in operation. ATTENTION! The encoder is designed to be assembled only one time, otherwise the guarantee will be voided. Note: see IMPORTANT NOTICE (page 11) PWB encoders GmbH Am Goldberg 2 D-99817 Eisenach Germany info@pwb-encoders.com / www.pwb-encoders.com

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Available accessories Standard cable Cable 300 mm length UL 10002 / AWG28 with female housing connector: Wennmacher CX-H-125-8 with CX-T125F terminals M2 Cable 300 mm length UL1061 / AWG26 with female housing connector: Molex 51021-0800 with 50079-8000 terminals Note: M1/M2: see ordering codes Adapter cable Twisted adapter cable 500 mm length UL10002 / AWG28 with female housing connector: 8-pin Wennmacher connector (Wennmacher CX-H-125-8 Housing with CX-T125F terminals) to a 10-pin Molex connector (Molex 90142-0010 housing with...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions Ordering codes Supply voltage Output type Shaft diameter Tenperature range Connector version adapter cable ** w ith out cable C: side connector + standard cable ** Centering gauge Available accessories (no parts of standard delivery): - standard cable 300 mm length - adapter cable 500 mm length - adapter plates for different motors - centering gauge for different motor shafts (highly recommended for correct assembly) - fastening screws 2 pcs DIN 965 M3 X 8 PWB encoders GmbH RESTRICTED THIS DOCUMENT AND ANY ASSOCIATED DATA...

data sheet AE30-F www.pwb-encoders.com Motion Control Solutions IMPORTANT NOTICE The encoder is so designed that it may be assembled only one time, otherwise the guarantee will be voided. The guarantee will be voided by misuse, accident, modification, unsuitable physical or operating environment, operation in other than the specified operating environment, or failure caused by a product for which PWB encoders GmbH is not responsible. PWB encoders GmbH reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services also...