dB ULTRASONIC TRANSDUCER SERIES Compact, low-power design that gives exceptional results even in challenging situations. Non-contact ultrasonic transducers to create the perfect solution for your application. Previously, users had a choice between high-voltage, frequencydependent transducers that were susceptible to electrical noise and needed special, protected interconnecting cables, and weak, low-power transducers that had good hazardous area performance but performed poorly in any but the simplest application. The dB ultrasonic transducer range has changed all of that, creating a compact, low power transducer design that can be Intrinsically Safe certified and uses standard interconnecting cables, yet produces extremely high acoustic power to give exceptional results in a wide variety of applications. Features & Benefits Combine a dB ultrasonic transducer with any of Pulsar’s Ultra, FlowCERT, Zenith, Quantum, or Blackbox control units to create the perfect solution for your application. All transducers have flammable atmosphere approval as standard. Standard transducer bodies are made from Valox 357 PBT with a special foam radiating face. Some are available with both body and sealed front face in PVDF for corrosive applications. Flanged Transducers Flange options are available for dB3, dB6, dB10, and dB15 transducers, ANSI or DIN specification, all featuring full PTFE THE RIGHT METER FOR • Wet Well Level • Pump Control Measurement • Tank Level • Shaft Tank • Silo Level • Digester Levels Measurement Measurement coating on the process wetted side. Various flange sizes are available. The maximum vessel pressure on flanges is 0.5 bar (7 psi). These incorporate the performance features of the standard products but additionally offer a front thread mount option to suit threaded nozzles or flanged tank entries. These integral flange options are available with the standard family of transducers, up to the dB15 size. Foam Face A foam faced option is available for all the standard range transducers to provide more acoustic power

DB ULTR A SONIC TR ANSDUCER SERIES output in dry, dusty environments. This higher acoustic power output increases return echo strength in these dry applications. Submergence Shield A shield can be fitted to keep the transducer face clean and dry in applications at risk of submergence. In the case of submergence, the controller can be asked to fail high, low, or hold the last reading. When the level drops back below the shield, it allows the controller to resume operation with a clean transducer face. The shield can be fitted to the dB3, dB6, dB10, dB15, and dB25 standard transducers. dBMACH3:...

Technical Specifications PHYSICAL: TRANSDUCER SPECIFIC Measurement Range: Sensor Body Material: Valox 357 U and syntactic foam face Cable Lengths: Standard = 5 m, 10 m, 20 m, or 30 m (16.4 ft, 32.8 ft, 65.6 ft, or 98.4 ft). Optional: up to 150 m (492 ft) maximum (increments of 10 m (32.8 ft) only) Maximum Separation: Mounting Connection: Enclosure Protection: Standard: -40° C to +90° C (-40° F to +194° F) Hazardous area versions: -40° C to +75° C (-40° F to +167° F) 2014/30/EU to EMC & 2014/34/EU ATEX Directives. Standards applied: EN 60079-0:2012+A11:2013/ EN 60079-11:2012 / EN 60079-18:2009...

0.25% or 6 mm (0.2 in) whichever is greater 0.01% or 2 mm (0.08 in) whichever is greater Delivering the Measure of Possibility INFO@PUL SAR ME A SUR EMENT.COM Pulsar Measurement is a trading name of Pulsar Process Measurement, Ltd. Copyright © 2020 Pulsar Measurement Registered Address: 1 Chamberlain Square CS, Birmingham B3 3AX Registered No.: 3345604 England & Wales