An IDEX Water & Wastewater Business Model Selection Guide & Product List Series M Mechanical Metering Pumps

IMPORTANT INFORMATION WHEN PLACING AN ORDER 1) Fax, mail or telephone orders directly to the Customer Service Department: Pulsafeeder Incorporated—A Unit of IDEX Corporation Standard Product Operations 27101 Airport Road, Punta Gorda, Florida, USA 33982-2462 E-Mail: [email protected] Telephone: 800-333-6677 or 941-575-3800 Fax: 800-456-4085 or 941-575-4085 Engineered Products Operations 2883 Brighton Henrietta Town Line Road, Rochester, New York, USA 14623 Telephone: 585-292-8000 Fax: 585-424-5619 www.pulsafeeder.com Please have the following information available when placing an order:...

Table of Contents Model Selection Guide Standard Motor Selections Metering Pump Controller - MPC Leak Detection / KOPkits Application Benefits: • Reliable Metering Performance • Simple Installation • Robust Design • Environmental Design • Low Cost of Ownership Follow the step by step approach presented in this guide to select the features you need. When you’re through you will have the exact model number for the PULSAtron Series M pump you want. Applications assistance is available through our Application Engineering Department, Rochester, NY. USA. Standard Lead Time is three weeks. Consult factory...

11, 12, 13, 14, 15 Options Position 10 is a dash Connection Type Size Motor Frame Adaptor Configuration Control Type Liquid End Construction Model Note: See notes on viscosity and multiplexing at the end of this section. PRESSURE AND CAPACITY @ 60 HZ, 1725 RPM Plastic Construction Metal Construction Conn. Size, Inch Conn. Size, Inch Suct. Disch.

PRESSURE AND CAPACITY @ 60 HZ, 1725 RPM Plastic Construction Metal Construction Conn. Size, Inch Conn. Size, Inch Suct. Disch. PRESSURE AND CAPACITY @ 50 HZ, 1425 RPM Plastic Construction Metal Construction Conn. Size, Inch Conn. Size, Inch Suct. Disch.

PRESSURE AND CAPACITY @ 50 HZ, 1425 RPM Plastic Construction Metal Construction Conn. Size, Inch Conn. Size, Inch 1. VISCOSITIES: For viscosities up to 3000 cp. select the pump stroking rates as follows: 2. MULTIPLEXING: For duplexing, select the same stroking rate (SPM) for both pumps. The power requirement for a duplex is one motor size larger than the normal motor size required largest pump of the two. If both pumps discharge to a common line, the rated discharge pressure will be the lowest of the pump pair. For multiplexing configurations of three or more pumps, consult factory. POSITION...

NOTES: (1) No power cord supplied, Direct wiring required. (2) Inverter Ready motors provide a 4:1 speed turndown with a separate AC Inverter (3) Inverter Duty motors provide 10:1 speed turndown with a separate AC Inverter (4) XP Motors are suitable for Class 1 Division 1 Group D only. Select type of MPC in Position 6 of the pump configuratin Configure an MPC as shown on page 8 Add this MPC model number to the order Select MPC price adder from the pricing table on page 9 Select motor from table on page 9 and add to the order as a line item with $0.

METERING PUMP CONTROLLER MPC - Automatic Flow Controller for Series M Pumps The MPC is a speed based automatic flow controller designed to be compact, simple to commission and use, and provide flexibility for control of a metering pump. Selecting an MPC Model Number: The MPC Model Number is a 15 digit number. MP_ _ _ _ _ _ _ _ - _ _ _ _ Position 3: Enclosure Type – Identifies the enclosure rating of the pump mounted controller (base unit) C = NEMA 4X Position 4: Pump Model P = Series M Mechanical Diaphragm Pump Position 5: Motor Power Input – Selected by the table on page 9: A = 1/4 hp (0.18...

9 EXTRA CABLE: The MPC remote can be located up to 1000 feet (305m) away from the pump. To order extra cable with the pump just add the line item part number NP530147-000 per foot to the order. Example: If you want 62 ft of cable, order 62 pieces of NP530147-000. PANEL MOUNT: The MPC remote is already a NEMA 4X (IP56) rated enclosure. Instead of integrating this into a control panel, we suggest mounting the remote “as is” on the outside of a panel or next to a panel on the wall. The bracket for wall or panel mounting is the same bracket that comes as standard on the pump. There is no chassis...

10 LEAK DETECTION: This illustration indicates the arrangement of the leak detection offering. Notice that the pressure switch is located behind the reagent head and does NOT thread into the reagent head. KOPkits KEEP ON PUMPING Kits Save You Money and Time Pulsafeeder has built a reputation for superior reliability by supplying carefully designed, high quality equipment. Even the best equipment, however, requires a minimal amount of maintenance. KOPkits are designed to guard against unnecessary down-time and assure you of the highest level of efficient service from your PULSAR Series M pumps....

11 Liquid End Construction Selection KOPkit # Less Material Code and Conn. Type KOPkit List Price G, P, W PVC(2) NOTES: See previous page for instructions. For pumps with leak detection, order the same kits listed here. The secondary (rear) diaphragm may be ordered separately. (1) Recommended for applications handling commercial concentrated sulfuric acid (66° Be/ 93+%). (2) Recommended for applications handling sodium hypochlorite. Pump Model KOPkit # Less Material Code and Conn. Type Pump Model KOPkit # Less Material Code and Conn. Type Pump Model KOPkit # Less Material Code and Conn. Type...

Manufacturer’s Equipment Warranty a. Pulsafeeder warrants all pumps and controllers of its manufacture to be free of defects in material or workmanship. Liability under this policy extends for 24 months from date of shipment from the factory. The manufacturer’s liability is limited to repair or replace- ment of any failed equipment or part which is proven defective in material or workmanship upon manufacturer’s examination. This warranty does not include removal or installation costs and in no event shall the manufacturer’s liability exceed the selling price of such equipment or part. b. The...