5 A with power boost CB scheme Data sheet Input: AC 230V / 115V Output: 24V / 5A Power boost up to 6A High overload current, no switch-off Quasi-Wide-Range Input Robust mechanics and EMC Input Input voltage AC100-120/200-240 V (switchable), 47-63 Hz (85-132 VAC / 176-264 VAC, 210-375 VDC, see also „Output: Continuous Loading“) < 2.6 A (switch in 115V position) < 1.4 A (switch in 230V position) • DCin at open output typ. 5 mA (preserves battery sources) Inrush current Quasi-Wide-Range Input: With the switch in the 230V position the power-supply unit operates at low and moderate loads (until 3 A) at any input voltage between 95 and 264 V AC (see ’Output’ below). Note: At DC input, always leave the switch in the 230V position Input current Output voltage Output noise suppression Radiated EMI values below EN 61000-6-3, even when using long, unscreened output cables. Ambient temperature range Tamb Operation: -10°C...+70°C (>60°C: Derating) Storage: -25°C...+85°C Continuous loading (at Tamb= -10°C...+60°C, 230V 176-264 V ACin 5 A / 6 A * convection cooling), see 95-176 V ACin 3 A also diagram overleaf. 210-375 V DCin 5 A / 6 A * For start at Tamb< 0°C and 150-210 V DCin 3 A low input voltage, please contact PULS. 100-150 V DCin 2 A Output is protected 115V 85-132 V ACin 5 A / 6 A * against short circuit, * short-term 6 A (< 1 min), at 45°C or forced cooling open circuit and overload even continuous To be fused with a 10A, B-type 'circuit-breaker' switch based on the usual thermomagn. overload sensing principle (used anyway to fuse the input lines). In addition, the unit contains an internal fuse (not accessible) EN 61000-3-2 (harmonic current emissions) is fulfilled Voltage regulation better than 2% Vout overall Transient handling Transient resistance acc. to VDE 0160 / W2 (750 V / 1.3 ms), for all load conditions. Ripple / Noise < 50 mVPP, (20 MHz bandw., 50 Ω measurem.) Overvolt. protection Parallel operation yes; current sharing available on request Power back immunity Front panel indicator Green LED, goes out at Vout <18V Efficiency, Reliability etc.* Efficiency Life cycle (electrolytics) The unit exclusively uses longlife electrolytics, specified for +105°C (cf. ’The SilverLine’, p.2). Construction / Mechanics* Housing dimensions and Weight 64 mm x 124 mm x 102 mm (+ DIN rail) • WxHxD above/below 25 mm recommended • Free space for left/right 15 mm recommended ventilation 620 g • Weight Design advantages: • All connection blocks are easy to reach as mounted at the front panel. • Input and output are strictly apart from each other and so cannot be mixed up (Input below, output above). * For further information see data sheets „The SilverLine“, „SilverLine Family Branches“ and mechanics data sheet Start / Overload Behaviour Startup delay Rise time Overload Behaviour • Special PULS Overload Design (see diagram overleaf) • 20% power boost – no disconnection, no hiccup if overloaded – high overload current (up to 1.9 INom), Vout is gradually reduced with increasing current. – 6A short-term, at 45°C or forced cooling even continuous Advantages: • High short-circuit current, giving large ’start-up window’: unit starts reliably even with awkward loads (DC-DC converters, motors). • No ’sticking’ such as can occur with fold-back characteristics • Secondary fuses operate reliably Order information Order number (Basic version*) (N+1 redundancy*) (Safety Cover*) Screw mounting set, two needed per unit 1/2

Data sheet Output Current over Input Voltage (min.) Input voltage VDCin [V] Input voltage VACin [V] For further information, especially about • Safety, Approvals see page 2 of the „The SilverLine" data sheet. see SilverLine mechanics data sheetSL2.5/SL5/SL10 Unless otherwise stated, specifications are valid for AC 230V inputvoltage, +25°C ambient temperature, and 5 min. run-in time. They are subject to change without prior notice. Your partner in power supply: Power Supply