Catalogs >
PULS GmbH >
SL10.105

SL10.105
2Pages

Catalog excerpts

Power in square, PFC CB scheme Data sheet Input: AC 230/115V, DC 240...375V Output: 24-28V/240W Power boost up to 288W High overload current, no switch-off Robust mechanics and EMC Very low leakage current Input Input voltage Output voltage DC 24-28V, adjustable by (covered) front panel potentiometer; preset: 24.5V ±0.5% Adj. range guaranteed Output noise suppression Radiated EMI values below EN 61000-6-3, even when using long, unscreened output cables. Note: At DC input, always leave the switch in the 230V position Input current <6A (switch in 115V position) <2.8A (switch in 230V position) • DCin at open output 8mA (preserves battery sources) Inrush current Ambient temperature Operation: 0°C...+70°C (>60°C: Derating) Storage: -25°C...+85°C range Tamb Unit is internally fused (fuse not accessible). For external fusing of unit and for input line protection, use circuit breaker with B-characteristic 10A or slower action, or alternatively T10A HBC fuse. Harmonic current emissions (PFC) Output is protected against short-circuit, open circuit and overload Transient handling Hold up time acc. EN 61000-3-2 Power factor: better than 0.68 at nominal load Transient resistance acc. to VDE 0160 / W2 (750V/1.3ms), for all load conditions. >20ms (at AC 196V, 24V/10A) (see diagram overleaf) Voltage regulation better than 2% Vout overall Ripple / Noise Overvolt. protection Parallel operation yes, current sharing available on request Power back immunity 34V Efficiency, Reliability etc.* Efficiency Life cycle (electrolytics) The unit exclusively uses longlife electrolytics, specified for +105°C (cf. ’The SilverLine’, p.2). Start / Overload Behaviour Startup delay Rise time Overload Behaviour • Special PULS Over- – no disconnection, no hiccup if overloaded – high overload current (up to 1.6 INom), load Design (see Vout is gradually reduced with increasing diagram overleaf) current. • 20% power boost – 12A short-term, at 45°C or forced cooling even continuous Front panel indicator Green LED on front panel Construction / Mechanics* Housing dimensions and Weight 120mm x 124mm x 102mm (+ DIN rail) • WxHxD above/below 25mm recommended • Free space for left/right 15mm recommended ventilation 1195g • Weight Design advantages: • All connection blocks are easy to reach as mounted at the front panel. • Very low leakage current >0,5mA, suitable for medical applications. * For further information see data sheets „The SilverLine“, „SilverLine Family Branches“ and mechanics data sheet Advantages: • High short-circuit current, giving large ’start-up window’: unit starts reliably even with awkward loads (DC-DC converters, motors). • No ’sticking’ such as can occur with fold-back characteristics • Secondary fuses operate more reliably Order information Order number Screw mounting set, two needed per unit

Open the catalog to page 1

Data sheet Functional diagrams Output characteristic (min.) Vout range Output voltage Vout [V 230 V ACin / 24 V DCout 230 V ACin / 28 V DCout 7 9 Ourput current Iout [A] Output current Iout [A] Hold-up time (typ., at Vout =24V) Partial load Nominal load Power Boost Partial load Nominal load Partial load Nominal load Power Boost 140 160 180 200 220 Input Voltage V ACin [V] with Partial Load = 120W 270 290 310 330 Input Voltage VDCin [V] For further information, especially about • EMC • Connections • Safety, Approvals • Mechanics and Mounting, see page 2 of the „The SilverLine“ data sheet....

Open the catalog to page 2