QS10.301 30V, 8A, SINGLE PHASE INPUT POWER SUPPLY AC 100-240V Wide-range Input Width only 60mm Efficiency up to 93.5% 150% (360W) Peak Load Capability Easy Fuse Tripping due to High Overload Current Active Power Factor Correction (PFC) Negligible low Inrush Current Surge Short-term Operation down to 60Vac and up to 300Vac Full Power Between -25°C and +60°C DC-OK Relay Contact Quick-connect Spring-clamp Terminals 3 Year Warranty GENERAL DESCRIPTION SHORT-FORM DATA The most outstanding features of this Dimension QSeries DIN-rail power supply are the high efficiency and the small size, which are achieved by a synchronous rectification and further novel design details. The QSeries is part of the Dimension family, existing alongside the lower featured C-Series. Output voltage Adjustment range Output current With short-term peak power capability of 150% and built-in large sized output capacitors, these features help start motors, charge capacitors and absorb reverse energy and often allow a unit of a lower wattage class to be used. High immunity to transients and power surges as well as low electromagnetic emission makes usage in nearly every environment possible. The integrated output power manager, a wide range input voltage design and virtually no input inrush current make installation and usage simple. Diagnostics are easy due to the dry DC-ok contact, a green DC-ok LED and red overload LED. DC 30V 28 – 32V 8A 12A Output power 240W 360W Output ripple < 50mVpp Input voltage AC 100-240V Mains frequency 50-60Hz AC Input current 2.22 / 1.22A Power factor 0.98 / 0.92 AC Inrush current typ. 4 / 7A peak Efficiency 92.6 / 93.5% Losses 19.1 / 16.7W Temperature range -25°C to +70°C Derating 6W/°C Hold-up time typ. 22 / 23ms Dimensions 60x124x117mm Unique quick-connect spring-clamp terminals allow a safe and fast installation and a large international approval package for a variety of applications makes this unit suitable for nearly every situation. ORDER NUMBERS Power Supply Wall mount bracket Side mount bracket Redundancy module Dec. 2014 / Rev. 2.2 DS-QS10.301-EN All parameters are specified at 30V, 8A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted. www.pulspower.com Phone +49 89 9278 0

QS10.301 30V, 8A, SINGLE PHASE INPUT The information presented in this document is believed to be accurate and reliable and may change without notice. No part of this document may be reproduced or utilized in any form without permission in writing from the publisher. PE is the abbreviation for Protective Earth and has the same meaning as the symbol Earth, Ground This document uses the term “earth” which is the same as the U.S. term “ground”. To be defined, value or description will follow later. A figure displayed with the AC or DC before the value represents a nominal voltage with standard tolerances...

QS10.301 30V, 8A, SINGLE PHASE INPUT 1. INTENDED USE This device is designed for installation in an enclosure and is intended for the general use such as in industrial control, office, communication, and instrumentation equipment. Do not use this power supply in aircraft, trains, nuclear equipment or similar systems where malfunction may cause severe personal injury or threaten human life. This device is designed for use in hazardous, non-hazardous, ordinary or unclassified locations. 2. INSTALLATION REQUIREMENTS This device may only be installed and put into operation by qualified personnel....

QS10.301 30V, 8A, SINGLE PHASE INPUT 3. AC-INPUT AC input AC input range nom. AC 100-240V suitable for TN-, TT- and IT mains networks min. 85-276Vac continuous operation min. 60-85Vac full power for 200ms, no damage between 0 and 85Vac min. 276-300Vac < 500ms max. 276Vac continuous, IEC 62103 nom. 50–60Hz ±6% typ. 81Vac steady-state value, see Fig. 3-1 typ. 63Vac steady-state value, see Fig. 3-1 typ. 55Vac dynamic value See recommendations in chapter 22.4. Allowed voltage L or N to earth Input frequency Turn-on voltage Shut-down voltage External input protection Input current Power factor *)...

QS10.301 30V, 8A, SINGLE PHASE INPUT 4. DC-INPUT DC input DC input range DC input current Allowed Voltage L/N to Earth Turn-on voltage Shut-down voltage Instructions for DC use: a) Use a battery or similar DC source. For other sources contact PULS b) Connect +pole to L and –pole to N. c) Connect the PE terminal to a earth wire or to the machine ground. -20%/+25% continuous operation 110Vdc, at 30V, 8A continuous, IEC 62103 steady state value steady state value 5. INPUT INRUSH CURRENT An active inrush limitation circuit limits the input inrush current after turn-on of the input voltage and after...

QS10.301 30V, 8A, SINGLE PHASE INPUT 6. OUTPUT Output voltage Adjustment range BonusPower® time BonusPower® recovery time Overload behaviour Short-circuit current Output capacitance *) Factory setting Line regulation Load regulation Ripple and noise voltage Output current guaranteed at clockwise end position of potentiometer ±0.2%, at full load, cold unit 60-300Vac static value, 0A 8A 20Hz to 20MHz, 50Ohm continuously available at 28V, see Fig. 6-1 continuously available at 30V, see Fig. 6-1 continuously available at 32V, see Fig. 6-1 short term available BonusPower® *), at 28V, for typical 4s,...

QS10.301 30V, 8A, SINGLE PHASE INPUT Fig. 6-1 Output voltage vs. output current, typ. Adjustment Range Output Voltage Bonus Time Fig. 6-2 Bonus time vs. output power Output Current Fig. 6-3 BonusPower® recovery time Limitation by Power Manager Output Voltage Bonus Time Recovery Time Bonus Power disabled The BonusPower® is available as soon as power comes on and immediately after the end of an output short circuit or output overload. Fig. 6-4 BonusPower® after input turn-on Fig. 6-5 BonusPower® after output short Input Voltage Output Voltage Output Voltage 150% Output Power Bonus Power Output...

□innenJSIOfU Q-Series 30V, 8A, SINGLE PHASE INPUT Hold-up Time Fig. 7-1 Hold-up time vs. input voltage Fig. 7-2 Shut-down behavior, definitions Hold-up Time Input Voltage Zero Transition Hold-up Time j 8. DC-OK RELAY CONTACT This feature monitors the output voltage, which is produced by the power supply itself. It is independent of a back-fed voltage from a unit connected in parallel to the power supply output. Contact closes As soon as the output voltage reaches the adjusted output voltage level. Contact opens As soon as the output voltage dips more than 10% below the adjusted output voltage....