CP10.121 12V, 16A, SINGLE PHASE INPUT POWER SUPPLY AC 100-240V Wide-range Input Width only 39mm Efficiency up to 94.3%, Excellent Partial Load Efficiency 20% Output Power Reserves Safe HiccupPLUS Overload Mode Easy Fuse Breaking due to High Overload Peak Current Active Power Factor Correction (PFC) Minimal Inrush Current Surge Full Power Between -25°C and +60°C Shut-down Input DC-OK Relay Contact Meets ITE, ATEX, Class I Div2 and SEMI F47 Requirements 3 Year Warranty GENERAL DESCRIPTION SHORT-FORM DATA The DIMENSION CP-Series units are high-end power supplies in a medium price range without compromising quality, reliability and performance. The CP-Series is part of the DIMENSION power supply family. The most outstanding features of CP10.121 are the high efficiency, advanced inrush current limitation, active PFC and the wide operational temperature range. Output voltage Adjustment range Output current The CP-Series includes all the essential basic functions. The devices have a power reserve of 20% included, which may even be used continuously at temperatures up to +45°C. Additionally, the CP10 can deliver three times the nominal output current for at least 12ms which helps to trip fuses on faulty output branches. High immunity to transients and power surges as well as low electromagnetic emission, a shut-down input, a DCOK relay contact and a large international approval package for a variety of applications makes this unit suitable for nearly every situation. ORDER NUMBERS Output power Output ripple AC Input voltage Mains frequency AC Input current DC Input Power factor AC Inrush current Efficiency Losses Temp. range Derating Hold-up time Dimensions Weight Power Supply Side mount bracket Redundancy module Marine, planned Feb. 2016 / Rev. 1.1 DS-CP10.121-EN All parameters are specified at 12V, 16A, 230Vac, 50Hz, 25°C ambient and after a 5 minutes run-in time unless otherwise noted. www.pulspower.com Phone +49 89 9278 0

CP10.121 12V, 16A, SINGLE PHASE INPUT The information presented in this document is believed to be accurate and reliable and may change without notice. No part of this document may be reproduced or utilized in any form without permission in writing from the publisher. PE is the abbreviation for Protective Earth and has the same meaning as the symbol Earth, Ground This document uses the term “earth” which is the same as the U.S. term “ground”. To be defined, value or description will follow later. A figure displayed with the AC or DC before the value represents a nominal voltage with standard...

CP10.121 12V, 16A, SINGLE PHASE INPUT 1. INTENDED USE This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office, communication, and instrumentation equipment. Do not use this power supply in equipment, where malfunction may cause severe personal injury or threaten human life. 2. INSTALLATION REQUIREMENTS This device may only be installed and put into operation by qualified personnel. This device does not contain serviceable parts. The tripping of an internal fuse is caused by an internal defect. If damage or...

CP10.121 12V, 16A, SINGLE PHASE INPUT 3. AC-INPUT AC input AC input range nom. AC 100-240V suitable for TN-, TT- and IT mains networks min. 85-264Vac continuous operation min. 264-300Vac < 500ms max. 300Vac continuous, IEC 62103 nom. 50–60Hz ±6% typ. 80Vac steady-state value, see Fig. 3-1 typ. 55Vac dynamic value (250ms) typ. 70Vac steady-state value, see Fig. 3-1 See recommendations in chapter 24.3. Allowed voltage L or N to earth Input frequency Turn-on voltage Shut-down voltage External input protection Turn-on overshoot External input protection Input current Power factor*) Crest factor**)...

CP10.121 12V, 16A, SINGLE PHASE INPUT 4. DC-INPUT DC input DC input range DC input current Allowed Voltage L/N to Earth Turn-on voltage Shut-down voltage Instructions for DC use: a) Use a battery or a similar DC source. A supply from the intermediate DC-bus of a frequency converter is not recommended and can cause a malfunction or damage the unit. b) Connect +pole to L and –pole to N. c) Connect the PE terminal to an earth wire or to the machine ground. ±20% continuous operation 110Vdc, at 12V, 16A continuous, IEC 62103 steady state value steady state value 5. INPUT INRUSH CURRENT An active inrush...

CP10.121 12V, 16A, SINGLE PHASE INPUT 6. OUTPUT Output voltage Adjustment range Factory settings Line regulation Load regulation Ripple and noise voltage Output current Output power Overload behaviour Short-circuit current Output capacitance guaranteed at clockwise end position of potentiometer ±0.2%, at full load and cold unit 85-300Vac static value, 0A 16A; see Fig. 6-1 20Hz to 20MHz, 50Ohm at 12V, ambient temperature <60°C, see Fig. 6-1 at 12V, ambient temperature <45°C, see Fig. 16-1 at 12V and 70°C ambient temperature, see Fig. 16-1 at 15V, ambient temperature <60°C, see Fig. 6-1 at 15V,...

□IfinenJSIOflJ CP-Series 12V, 16A, SINGLE PHASE INPUT Fig. 6-1 Output voltage vs. output current, Fig. 6-2 Dynamic output current capability, Output Voltage Output Voltage (dynamic behavior, < Fig. 6-3 Short-circuit on output. Hiccup1*"5 mode, typ. Short -circuit Hold-up Time Fig. 7-1 Hold-up time vs. input voltage Fig. 7-2 Shut-down behavior, definitions Input Voltage Zero Transition Hold-up Time All parameters are specified at 12V, 16A, 230Vac, 50Hz, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

CP10.121 12V, 16A, SINGLE PHASE INPUT 8. DC-OK RELAY CONTACT This feature monitors the output voltage on the output terminals of a running power supply. Contact closes Contact opens As soon as the output voltage reaches typ. 90% of the adjusted output voltage level. As soon as the output voltage dips more than 10% below the adjusted output voltage. Short dips will be extended to a signal length of 100ms. Dips shorter than 1ms will be ignored. max. 60Vdc 0.3A, 30Vdc 1A, 30Vac 0.5A resistive load min. 1mA at 5Vdc min. permissible load See dielectric strength table in section 18. Contact ratings...