PREMIUM-MF 13.56 MHz MIFARE reader
5Pages

PREMIUM-MF RFID card reader PREMIUM-MF 13.56 MHz MIFARE reader The PREMIUM-MF type is a contactless reader device in the frequency range of 13,56 MHz. This reader will read the unique ID number of a Mifare® card and output that code in any of many user selectable formats. Due to the fully potted housing, the reader can be installed both indoors and outdoors. An integrated DIP-switch allows easy selection of 1 of 13 possible output formats. A three-colour LED indication and audible tone enhance user feedback. Both beeper and LED’s can be controlled by the host system. Power supply : Power consumption : Transmitting Radio Frequency : Supported transponders : Typ. read range (@ 12V): Typ. read range (@ 5.0V): Indications : Data Output format : DC +5,0V to 13,6V Typ. 100mA 13.56 MHz Mifare® Std, Mifare® Ultralight, Mifare® DESFire, Mifare® PLUS S/X Contactless interface as per specification: ISO/IEC 14443 Type A NFC Passive mode (ISO 18092/NFC passive mode, initiator, selected tag types a.o. NTAG203, NTAG213) ISO card with 50mm coil : 50 mm ISO card with 50mm coil : 30 mm 3 LEDs (Greed/Red/Yellow) + Buzzer Buzzer emits a 60ms beep at 4 kHz when a transponder is read. In addition buzzer operates while BUZZER input is pulled low DIP-switch selectable : - Wiegand (58-bit, 42-bit, 34-bit and 26-bit) - Clock & Data ( 13, 10, 9 or 8 characters ) - Basic Clock&Data – 56 bits - RS232 (9600, 4800 or 2400 Bd) (EIA level) - TTL (9600, 4800 or 2400 Bd) Continuous (while tag in the field) or single transmission 10-wire cable ( 1 m length ) 90g -20°C ~ +60°C Mullion or wall mount ( Extra mounting plate is supplied with each reader ) 89 x 45 x 16 mm ( dimensions mounting plate : 89 x 45 x 7 mm ) Transmission : Connections : Weight : Operating Temperature : Mounting :  Dimensions : ProxTech International bvba Zakstraat 104, 9112 Sinaai ( Belgium ) Info @ proxtech.com

PREMIUM-MF RFID card reader Physical dimensions and mounting details : Centred cable exit hole All measurements in mm Drawing not to scale If the mounting plate is used the reader cable may be brought out of one of four exit points on the mounting plate: top, bottom, left or right. This enables the cable to be run on the surface of the wall. If no mounting plate is used, a minimum hole size of 6,5 mm must be drilled in the wall at the cable exit position as shown above to allow the cable to exit perpendicular to the reader. The optional mounting plate may also be used when mounting the...

Proxi rech International PREM1UM-MF RFID card readerConnections : Colour Note : LED and BUZZER inputs are active low. The input is internally pulled high and may be pulled low by an open collector transistor or driven low by the output of a 5 V CMOS or TTL gate. The 6-way switch is used to select the output format and LED mode. The required setting is selected from the following tables: Output mode table

Proxi rech International PREM1UM-MF RFID card reader LED mode table Note : This “continuous transmission” mode can not be guaranteed to work properly on some controllers, depending on the data interfaces. However, the “single transmission” mode will work with all controllers. It is therefore recommended to test this function prior to site activation. The reader has an internal low dropout 5 V regulator and so for maximum performance the input voltage must be smooth DC between 5.5V and 13.6V. The reading distance is unchanged for input voltages between 5.5V and 13.6V. For input voltages...

Proxi rech International PREM1UM-MF RFID card readerMifare transponder UID architecture : Since the PREMIUM-MF supports different Mifare transponder types (mifare® Std, mifare® Ultralight, mifare® DESFire, mifare® PLUS S, mifare® PLUS X ), please keep in mind that each of these types have different UID lengths. Mifare Classic : 4 bytes Therefore if the complete UID needs to be read, it is essential to select an interface that will output sufficient data. For Mifare transponder versions with a 7 byte UID (mifare DESFire, Ultralight, Plus X), one of the following output modes is...