PREMIUM-EM
4Pages

PREMIUM-EM RFID card reader PREMIUM-EM 125 kHz RFID card reader The PREMIUMEM card reader is a contactless reader device supporting 125 kHz EM4x02 transponders and compatibles. Due to the fully potted housing, the reader can be installed both indoors and outdoors. An integrated DIP-switch allows an easy selection of the many integrated output formats. Three-colour LED indication and audible tone enhance user feedback. Both beeper and LED’s can be controlled by the host system. Power supply : Power consumption : Transmitting Radio Frequency : Supported transponders : DC +5,0V to 13,6V Typ. 100mA ( 80mA @ 5VDC ) 125KHz 40 bit read only transponders EM4x01 family, HiTag2 Public Mode A, TEMIC e5550 and equivalents  Typ. read range (@ 5.5V-13.6V): Key tag with 20mm coil : 85mm ISO card with 50mm coil : 175mm  Typ. read range (@ 5.0V): Key tag with 20mm coil : 80mm ISO card with 50mm coil : 160mm  Indications : 3 LEDs (Greed/Red/Yellow) + Buzzer Buzzer emits a 60ms beep at 4 kHz when a transponder is read. In addition sounder operates while BUZZER input is pulled low  Data Output format : DIP-switch selectable : - Wiegand (42-bit, 34-bit and 26-bit) - Clock & Data ( 13, 10, 9 or 8 characters ) - RS232 (9600, 4800 or 2400 Bd) (buffered) - RS232 (9600, 4800 or 2400 Bd) (TTL)  Transmission : Continuous (while tag in the field) or single transmission  Connections : 10-wire cable ( 1 m length )  Weight : 90g  Operating Temperature : -20°C ~ +60°C  Mounting : Mullion or wall mount ( Extra mounting plate is supplied with each reader )  Dimensions : 89 x 45 x 16 mm ( dimensions mounting plate : 89 x 45 x 7 mm ) ProxTech International bvba Zakstraat 104, 9112 Sinaai ( Belgium ) Info @ proxtech.com

PREMIUM-EM RFID card reader Physical dimensions and mounting details : Centred cable exit hole All measurements in mm Drawing not to scale If the mounting plate is used the reader cable may be brought out of one of four exit points on the mounting plate: top, bottom, left or right. This enables the cable to be run on the surface of the wall. If no mounting plate is used, a minimum hole size of 6,5 mm must be drilled in the wall at the cable exit position as shown above to allow the cable to exit perpendicular to the reader. The optional mounting plate may also be used when mounting the...

PREMIUM-EM RFID card reader Connections : Colour BLACK RED PURPLE BLUE GREEN Name 0V +VDC RS-232 TX BUZZER GRN-LED ORANGE YELLOW BROWN WHITE GREY RED-LED YEL-LED DATA / DATA1 CLOCK / DATA0 / TTL-TX CARD PRESENT Function Connect 0V from power supply. Connect +5V - +13.6V from power supply Output RS-232 Controls Buzzer Controls Green LED in LED Mode 1 or both Red and Green LEDs in LED Mode 2 Controls Red LED in LED Mode 1 Controls Yellow LED in LED Mode 1 Outputs RFID tag code in selected format Outputs RFID tag code in selected format Pulses low when an RFID tag is detected. It stays low...

PREMIUM-EM RFID card reader LED mode table Mode # 1 2 LED Mode 3 Individual LED’s each controlled by their own input RED/GREEN with single control line (GRN-LED) Note : In LED Mode 2, both RED and GREEN leds are controlled by the GRN-LED input. When the GRN-LED input is floating or pulled high, the RED led is on and the GREEN led is off. When the GRN-LED input is pulled low (connected to 0V) the GREEN led is on and the RED led is off. The YELLOW led is always off. Continuous/Single Transmission Mode Table Mode Continuous Operation While a tag is in the reader’s field the reader will...