PL500
4Pages

PL500 stand-alone access control PL500 stand-alone access control system PL500 access control system is a stand-alone contactless reader and control unit in the frequency range of 125 kHz. This reader supports the transponder types EM4x02 and Hitag 2 in Public Mode A. The system has a 500 user memory. Memory and relay circuits are contained in a robust plastic housing allowing for simple installation. The minimum connection only requires AC or DC power and a door strike. Due to the fully potted housing, the reader can be installed both indoors and outdoors. The reader is suitable for controlling access into a home or small business. When a valid tag is presented to the reader, the relay will either pulse or toggle. Three LEDs (RED, GREEN and YELLOW) indicate the current state of the relay during normal operation or are used to indicate different programming modes. Power supply : Power consumption : Transmitting Radio Frequency : Supported transponders : Indications : Programming : Relay operation mode : Relay contact ratings : o Maximum current o Maximum ratings Connections : Weight : Operating Temperature : Mounting : Dimensions : Housing : +10,2 to +13,6 VDC or 10 to 12 VAC Typ. 110mA 125KHz 40 bit read only transponders EM4x01 family, HiTag2 Public Mode A, TEMIC e5550 and equivalent Key tag with 20mm coil : 50 mm ISO card with 50mm coil : 90 mm 3 LEDs (Greed/Red/Yellow) Adding and deleting tags is done by simple use of a Master Tag. The optional Tag Simulator / Programming Unit allows the programming (adding & deleting) of lost tags Pulse mode (the relay operates for a pre-set time for each valid tag read) or Toggle mode (the relay state changes for each valid tag read) 2,0 A @ 15VDC 1.2A @ 24VDC 0.6A @ 50VDC DC 30W 125 VDC AC 62VA 250 VAC 8-way connector 90g -20°C ~ +60°C installation into a 55 mm switchbox 48 x 48 x 37 mm ( dimensions mounting plate : 71 x 71 x 1,2 mm ) ABS plastic – fully potted IP65 ProxTech International bvba Zakstraat 104, 9112 Sinaai ( Belgium ) Info @ proxtech.com

PL500 stand-alone access control Connections : The table below details the function of each connection: PIN RELAY NC RELAY NO RELAY COM EXIT CLEAR COM AC/DC AC/DC Function Voltage free normally closed contact of the 1A relay Voltage free normally open contact of the 1A relay Voltage free common contact of the 1A relay Connect normally open exit push button between EXIT and COM Connect between CLEAR and COM to clear memory after power up 0V connection for EXIT and CLEAR Power: 10.2-13.6V DC or 10-12V AC Power: 10.2-13.6V DC or 10-12V AC Operation : Normal Operation The PL500 has two modes of...

PL500 stand-alone access control Pulse Mode This mode is typically required in access control applications. On power-up the YELLOW led will be on and the relay will be off (NC shorted to COM). When a valid tag is read the relay will operate for the programmed Relay Pulse time (between 1 and 60 seconds). While the relay is on, the GREEN led will be on. When the relay switches off the GREEN led will turn off again. An invalid tag will cause the RED led to come on for 2 seconds. Programming The Master Tag is the first tag presented to the PL500 when it is in the Add Master state. All...

PL500 stand-alone access control Clear Memory To delete all the tags from the memory including the Master Tag and Strike time, place the unit in the CLEAR MEMORY state. 1. Read the Master Tag three times with a time between reads of less than 2 seconds. 2. The GREEN and RED leds will light. 3. Wait for the GREEN and RED leds to start flashing. The PL500 is now in the CLEAR MEMORY state. Now present any tag except the Master Tag to the reader and all memory will be cleared. Alternatively, read the Master Tag to abort this function. Once the memory is cleared all leds will flash to indicate...