Pullers
36Pages

we don’t just make pullers, we make pulling systems. The best way to remove a gear or bearing from its housing is with a tool designed just for that job: a puller. This simple but ingenious device consists of a set of movable jaws attached at one end to a forcing screw. Turning the screw engages the jaws, causing them to pull the part from its housing. The puller is a real force multiplier: It will pull a wheel, gear, or bearing with much more force than it takes to turn the forcing screw. It will also reach into the most difficult of spots and will pull the part in a way that protects it – and you – from harm.

6 TON PROTO-EASE™ 2-WAY/3-WAY CONE PULLER SET

» Makes 12 of the most commonly used pullers: Internal External and Slide hammer. » Designed for pulling machine parts up to 8" in diameter with reach depths to over 7". » Makes over 12 different adjustable and straight jaw pullers J4211BA Adjustable Jaw Block Assembly 3 J4332 Bearing Separator, 4-3/8" Capacity 1 WARNING: WORK SAFELY WITH TOOLS. WEAR SAFETY GOGGLES

» Makes over 20 of the most often used pullers: Internal, External, Slide Hammer Rear Axle, Harmonic Balancer, etc, J42B0R T-Handle Slide Rod, 24" Long J4275R Short Slide Rod, 12-3/4" Long J4277B Rear Axle Flange Foot J4280 Set Puller Blind Bearing J4331 Gear and Bearing Separator 10 TON PROTO-ERSE™ WIDE PULLER SET » Required for large parts with heavy press-fits > Reaches to over 12" and spread of 11" » Makes over 1B different adjustable J4231A Adjustable Jaw Block Assembly 3 Made in USA accurate at time of printing, consult www.protoindustrial.com for updated information S= Made in USA BS...

PROTO-ERSE ™ BERRINC SEPRRRTOR » Removes gears and bearings too close to another surface for a puller jaw grip, or where the pulled out part must be protected » Case provides space for step plates and assorted accessories Gear and Bearing Separator, Gear and Bearing Separator Gear and Bearing Separator, Gear and Bearing Separator, 6" Capacity Blow-Molded Case » Presses parts into place without hydraulics » Functions as many different pullers either by itself or in combination with other Proto® Pullers. J4235AA Adapter, 3/4"-12 Female x 5/8" Male Adapter, 3/4"-12 Female Acme x 5/8" WARNING:...

PROTO-EASE™ GENERAL PULLER SET Product #: J4245 Description Cap Screw, 3/8"-24 UNF x 3" Spring Clip Dual-Reach Jaws Long Narrow Jaw Cap Screw Jaw Jaw Spring Clip Dual Reach Jaw Narrow Jaw Step Plate Adapter Set Inside Jaw, 2" Reach Slotted Crossarm 2-Way/3-Way Cap Screw, 3/8"-16 UNC x 4" 2-Way Crossarm 2-Way/3-Way Crossarm 3-Way Crossarm, 11" Long 10 Ton 2-Way Straight Jaw Puller Set 6 Ton 2-Way/3-Way Cone Puller Set Inside-Hook Jaw 2-1/2 lbs. Slide Hammer T-Handle Slide Rod, 24" Long Set Puller Blind Bearing Gear and Bearing Separator, 2-13/32" Capacity Gear and Bearing Separator, 4-3/8"...

» Covers most maintenance operations using standard pullers. » Contains components necessary to assemble all full-interchange system pullers except ProtoL* Press-N-PuH™ Pullers. J4260R T-Handle Slide Rod, 24" Long J4277B Rear Axle Flange Foot J4280 Set Puller Blind Bearing J4211BA Adjustable Jaw Block Assembly 3 J4231A Adjustable Jaw Block Assembly 3 J4331 Bearing Separator, 2-13/32" Capacity J4333A Bearing Separator, 6" Capacity J4D4D Step Plate Adapter Set J4040-12 Step Plate, 2-1/8" Bore J4040-13 Step Plate, 2-1/4" Bore J4040-14 Step Plate, 2-3/8" Bore WARNING: WORK SAFELY WITH TOOLS....

PROTO-EHSE™ MASTER PULLER SET (WITH BOH) » Covers most maintenance operations using standard pullers > Contains components necessary to assemble all full-interchange system pullers except Proto® Press-N-PulH Pullers J42B0R T-Handle Slide Rod, 24" Long J4277B Rear Axle Flange Foot J4280 Set Puller Blind Bearing J4211BA Adjustable Jaw Block Assembly 3 J4231A Adjustable Jaw Block Assembly 3 J4331 Bearing Separator, 2-13/32" Capacity J4333A Bearing Separator, 6" Capacity J4040 Step Plate Adapter Set J4040-12 Step Plate, 2-1/8" Bore J4040-13 Step Plate, 2-1/4" Bore J4040-14 Step Plate, 2-3/8"...

OPERATIONAL FEATURES - 6 TON PROTO-EASE™ CONE PULLERS Forcing screws should be easy to turn—and most are—when the load is fairly light. But tough pulling jobs are a different story. Most screws tighten up when the going gets rough, resulting in far less output than you apply. Why? Because there’s frictional resistance. The thread and threaded hole are fighting each other all the way. Not with Proto®! We’ve got Acme threads to increase your muscle power. Acme is the thread with a long-lasting reputation for easy turning and smooth-as-silk performance. PULLERS & PULLER SETS Since the...

E TON PROTO-ERSE ™ 2-WRY/3-WRY CONE PULLER SET Contents Description Made in USA accurate at time of printing, consult www.protoindustrial.com for updated information. S= Made in USA B55 Made in USA with global components

6 TON PROTO-EASE™ 3-WAY CONE PULLER SET Product #: J4255 PULLERS & PULLER SETS Description Standard Detachable Tip Reversible Jaw, 4" Reach Pivot Pin Forcing Screw 3 Jaw Yoke Reversible Adjusting Nut 6 TON 3-WAY CONE PULLER Product #: J4257 Reach: 4" – Spread: 5". Weight (lbs): 2.59 Reach: 6" – Spread: 7". Weight (lbs): 2.50 Description Standard Detachable Tip Reversible Jaw, 6" Reach Jaw Pivot Pin Forcing Screw 3 Jaw Yoke Reversible Adjusting Nut WARNING: WORK SAFELY WITH TOOLS. WEAR SAFETY GOGGLES.

TYPICAL APPLICATIONS 6 TON PROTO-EASE™ WIDE PULLERS NO. J4217 PROTO-EASE™ 6 TON PROTO-EASE™ 2-WAY/3-WAY ADJUSTABLE JAW PULLER Adjustable jaws (A) reach around obstructions to grip parts inaccessible to straight jaws (B) Adjustable jaws (C) have greater reach capabilities than straight jaws (D) Pivot pin A quick release type jaw pin. Reversible Jaw Jaws slide into place along crossarm and may be positioned at unequal distances from the forcing screw for unusual pulling applications. The 6 ton wide puller shown below accepts all 3 ton and 6 ton jaws— adjustable and straight. Puller is used to...