Composite PLA - The Original Carbon Fiber - 5 Pages

Add to MyDirectIndustry favorites
Composite PLA - The Original Carbon Fiber

Catalog excerpts

SAFETY DATA SHEET    DOC VERSION: 1PROTO-PASTA CARBON FIBER PLA    PRINT DATE: 04/26/2016REV DATE:SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME:    Proto-pasta    Carbon Fiber    PLA SYNONYMS:    Proto-pasta    CFPLA RECOMMENDED USE:    For use in 3D printers at recommended temperatures MANUFACTURER: ADDRESS: EMERGENCY PHONE: OTHER CALLS: HOMEPAGE: Proto Plant 5601 East 18Th Street #102 Vancouver, WA 98661 503-877-5268 503-877-5268 www.protoplant.com Dustin Cram - Chief Engineer SECTION 2: HAZARDS IDENTIFICATION EMERGENCY OVERVIEW: This is a polymeric compound. All ingredients are encapsulated by the polymer and present no likelihood of exposure under normal conditions of processing and handling. GHS-US CLASSIFICATION This product is not classified under GHS SIGNAL WORD:    NONE HAZARDS THAT DO NOT RESULT IN CLASSIFICATION EYES:    Solid/dust may cause irritation due to mechanical action. Dust will not be generated under normal use conditions. SKIN:    Filament is not likely to cause irritation. Contact with molten material may cause thermal burns. BURNS:    Molten material will cause thermal burns, avoid contact. INHALATION:    Processing fumes may cause irritation to the respiratory tract, use in well ventilated areas only. CHRONIC HEALTH HAZARDS:    None known for this compound.

 Open the catalog to page 1

DOC VERSION: 1 PRINT DATE: 04/26/2016 REV DATE: SAFETY DATA SHEETPROTO-PASTA CARBON FIBER PLASECTION 3: COMPOSITION/INFORMATION ON INGREDIENTSINGREDIENTS_CAS NO._% WT Polylactide resin    9051-89-2    >85 EYES: First Aid not likely required. Flush with water. Consult physician if symptoms persist. SKIN: Wash with soap and water. For thermal burns, immediately flush with cold water. Do not attempt to remove polymer from skin. Obtain medical attention. INGESTION: Obtain immediate medical attention. For a poison emergency in the U.S. call 1-800-222-1222. INHALATION: Leave exposed area and seek...

 Open the catalog to page 2

SAFETY DATA SHEET DOC VERSION: 1 PRINT DATE: 04/26/2016 REV DATE: PROTO-PASTA CARBON FIBER PLA ENVIRONMENTAL PRECAUTIONS: Do not flush into surface water or sanitary sewer system. Do not allow material to contaminate ground water system. METHODS FOR CLEANING UP: Cut filament into short pieces to prevent tripping. Dispose of in suitable containers. SECTION 7: HANDLING AND STORAGE PRECAUTIONS: Proper purging and shut down procedures should be followed to avoid overheating of this compound. Use only at recommended printing temperatures. Product as shipped is not a combustible dust. Mechanical...

 Open the catalog to page 3

REV DATE: BOILING POINT/RANGE: Not applicable FLASH POINT: Not Determined EVAPORATION RATE: Not determined FLAMMABILITY: Combustible if heated UPPER/LOWER FLAMMABILITY OR EXPLOSIVE LIMITS: Not Determined VAPOR PRESSURE: Not Determined VAPOR DENSITY: Not Determined DENSITY: 1.30 g/cc WATER SOLUBILITY: Insoluble SOLUBILITY IN OTHER SOLVENTS: Not determined PARTITION COEFFICIENT: N-OCTANOL/WATER: Not Determined AUTO-IGNITION TEMPERATURE: 300C-400C DECOMPOSITION TEMPERATURE: 482F (250C) VISCOSITY: Not applicable SECTION 10: STABILITY AND REACTIVITY REACTIVITY: Stable when stored as...

 Open the catalog to page 4

SAFETY DATA SHEET DOC VERSION: 1 PRINT DATE: 04/26/2016 REV DATE: PROTO-PASTA CARBON FIBER PLA RESPIRATORTY OR SKIN SENSITIZATION: None Known GERM CELL MUTAGENICITY: Not Determined CARCINOGENICITY: None Known REPRODUCTIVE TOXICITY: Not Determined STOT-SINGLE EXPOSURE: Not Determined STOT-SINGLE EXPOSURE: Not Determined ASPITIATION HAZARD: None Known SECTION 12: ECOLOGICAL INFORMATION ECOTOXICITY EFFECTS: Not Determined DEGRADABILITY AND PERSISTENCE: Not Determined BIOACCUMULATIVE POTENTIAL: Not Determined MOBILITY IN SOIL: Not Determined SECTION 13: DISPOSAL CONSIDERATIONS WASTE DISPOSAL...

 Open the catalog to page 5

All Proto-Pasta catalogs and technical brochures

  1. Everyday PLA

    5 Pages