Product data sheet OxyTrans II

Product catalog summary

Overview
The OxyTrans is a two-wire process oxygen analyzer designed for accurate and economical measurement of oxygen at trace and percentage levels. It features a simple display and one-point calibration for easy setup.

Specifications

Measuring Ranges: Switchable between 0-10 ppm and 0-50% oxygen. Specific ranges include 0-10, 0-100, 0-1000, 0-10000 ppm and 0-0.25, 0-2.5, 0-25% O2.
Calibration: Can be performed with calibration gas for ppm or air for percentage range.
Accuracy: +/- 2% FSD at constant temperature, +/- 5% FSD from 0 to 50°C.
Resolution: 0.1 ppm for 0-100 ppm, 1 ppm for 0-1000 and 0-10000 ppm, 0.1% for 25%.
Response Time: 90% FSD at 25°C, varying from 10 to 45 seconds depending on range.
Operating Temperature: 0 - 50°C.
Pressure: 0.1 - 1 bar.
Signal Output: 4-20 mA/DC with HART communication.
Alarm Value: Standard at 3.8 mA, optional at 23 mA.
Voltage: 10-35 VDC with reverse voltage protection up to 40 VDC.
Load: Typically 470 Ohm.
Display: 6-digit alphanumeric with bar graph.
Housing: IP65 rated, size 120 x 160 x 65 mm, weight 1.2 kg.

Features

Compact and inexpensive design.
Switching ranges from 10,000 ppm to 10 ppm.
Long operating life sensor with no cross sensitivity to H2.
Zero calibration for low ppm measurement.
Stainless steel flow-through measuring cell, modular for easy repair.

Applications
The OxyTrans is suitable for use in various industries including semiconductor, gas manufacturing, metallurgical, chemical, heat treating, and bright annealing.

Contact Information
Pro-Chem Analytik GmbH & Co.KG, Neuer Bruchweg 1, 46509 Xanten. Tel: 02801/98510-70, Fax: 02801/98510-71, Email: [email protected], Website: www.prochem-online.com

Catalog excerpts

OxyTrans 4 – 20 mA Loop Powered two wire Oxygen Transmitter Two Wire Process Oxygen analyzer The Model OxyTrans is simple, accurate and economic measurement of Oxygen at trace and % levels. A simple Display and one point calibration allow easy and fast start-up of the instrument. optional  One User specific measuring range The unit will be available with ranges between 0-10 ppm and 0 – 50% of oxygen. The ppm range can be switch at 10.000/ 1.000/ 100/ 10 ppm and the % range at 25/ 2,5/ 0,25 % O2.  Sensor The OxyTrans uses a special fuel cell to measure the oxygen concentration. The sensor meets the industrial requirements for accuracy, sensitivity, easy to use and operating life.  Calibration The calibration of the instrument for trace oxygen measurements in gas, should be done with a calibration gas. The concentration can be chosen freely within the measuring range. In the percent range the unit can calibrated with air. A zero set point is also possible.  Features compact inexpensive switching ranges 10.000ppm to 10 ppm storage cost from 4 to 1 device reduced Sensor with long operating life IP65 enclosure reverse voltage protection and temperature compensation  No cross sensitivity to H2  zero calibration for measurement in low ppm rang         Flow-through measuring cell in Stainless Steel   The measuring cell is modular and is made of stainless steel A defective measuring cell can be repaired by replacing the defective part on

Open the catalog to page 1

Typical Types and Measuring ranges ( switchable ) • different sensors available Special ranges possible for higher values use OxyTrans 100 • manuell switch of Measuring ranges • 316 SS stainless steel Cell block Calibration : with calibration gas ppm or Response time Signal output Alarm value reverse voltage protection up to 40VDC optional Sensor housing with KF40 flans • Semi conductor industry • Metallurgical industries • Chemical industry • heat treating and bright annealing oxygen sensor 6 Digits, alphanumeric with bar graph Micro-Fuell Cell, Pro-Chem Analytik GmbH & Co.KG Neuer Bruchweg...

Open the catalog to page 2